Kyocera SLIDER JET KX18 User Manual

These limits are part of comprehensive

The FCC has granted an Equipment

guidelines and establish permitted levels of RF

energy for the general population. The guidelines

are based on standards that were developed by

independent scientific organizations through

periodic and thorough evaluation of scientific

studies. The standards include a substantial

safety margin designed to assure the safety of all

persons, regardless of age and health.

Authorization for this model phone with all

reported SAR levels evaluated as in compliance

with the FCC RF emission guidelines. SAR

information on this model phone is on file with

the FCC and can be found under the Display

Grant section http://www.fcc.gov/oet/fccid after

searching on the FCC ID: OVFKWC-KX18.

Additional information on SAR can be found on

the Cellular Telecommunications and Internet

Association (CTIA) web-site at

The exposure standard for wireless mobile

phones employs a unit of measurement known

as the Specific Absorption Rate, or SAR. The

SAR limit set by the FCC is 1.6 W/kg.* Tests for

SAR are conducted using standard operating

positions specified by the FCC with the phone

transmitting at its highest certified power level in

all tested frequency bands.

http://www.wow-com.com.

* In the United States and Canada, the SAR

limit for mobile phones used by the public is

1.6 watts/kg (W/kg) averaged over one gram of

tissue. The standard incorporates a substantial

margin of safety to give additional protection for

the public and to account for any variations

in measurements.

Although the SAR is determined at the highest

certified power level, the actual SAR level of the

phone while operating can be well below the

maximum value.

Caution

The user is cautioned that changes or

modifications not expressly approved by the

party responsible for compliance could void the

warranty and user’s authority to operate

the equipment.

This is because the phone is designed to operate

at multiple power levels so as to use only the

power required to reach the network. In general,

the closer you are to a wireless base station

antenna, the lower the power output.

Optimize your phone’s performance

Before a phone model is available for sale to the

public, it must be tested and certified to the FCC

that it does not exceed the limit established by

the government-adopted requirement for safe

exposure. The tests are performed in positions

and locations (e.g., at the ear and worn on the

body) as required by the FCC for each model.

Use the guidelines on page 2 to learn how to

optimize the performance and life of your phone

and battery.

Air bags

If your vehicle has an air bag, DO NOT place

installed or portable phone equipment or other

objects over the air bag or in the air bag

deployment area. If equipment is not properly

installed, you and your passengers risk

serious injury.

Body-worn measurements differ among phone

models, depending upon availability of

accessories and FCC requirements. While there

may be differences between the SAR levels of

various phones and at various positions, they all

meet the government requirement for

safe exposure.

Medical devices

Pacemakers—Warning to pacemaker wearers:

Wireless phones, when in the ‘on’ position, have

been shown to interfere with pacemakers.

User Guide for the Slider Jet Phone

iii

The phone should be kept at least six (6) inches

away from the pacemaker to reduce risk.

Blasting areas—Turn off your phone where blasting

is in progress. Observe restrictions, and follow

any regulations or rules.

The Health Industry Manufacturers Association

and the wireless technology research community

recommend that you follow these guidelines to

minimize the potential for interference.

Potentially explosive atmospheres—Turn off your

phone when you are in any area with a

potentially explosive atmosphere. Obey all signs

and instructions. Sparks in such areas could

cause an explosion or fire, resulting in bodily

injury or death.

•

Always keep the phone at least six inches

(15 centimeters) away from your pacemaker

when the phone is turned on.

•

Do not carry your phone near your heart.

Use the ear opposite the pacemaker.

If you have any reason to suspect that

interference is taking place, turn off your

phone immediately.

Areas with a potentially explosive atmosphere

are often, but not always, clearly marked.

They include:

•

fueling areas such as gas stations

below deck on boats

transfer or storage facilities for fuel or

chemicals

Hearing aids—Some digital wireless phones may

interfere with hearing aids. In the event of such

interference, you may want to consult your

service provider or call the customer service line

to discuss alternatives.

•

vehicles using liquefied petroleum gas, such

as propane or butane

areas where the air contains chemicals or

particles such as grain, dust, or metal

powders

Other medical devices—If you use any other personal

medical device, consult the manufacturer of the

device to determine if it is adequately shielded

from external RF energy. Your physician may be

able to help you obtain this information.

•

any other area where you would normally be

advised to turn off your vehicle engine

Use with care

In health care facilities—Turn your phone off in health

care facilities when instructed. Hospitals and

health care facilities may be using equipment

that is sensitive to external RF energy.

Use only in normal position (to ear). Avoid

dropping, hitting, bending, or sitting on

the phone.

Keep phone dry

Potentially unsafe areas

Posted facilities—Turn your phone off in any facility

when posted notices require you to do so.

If the phone gets wet, turn the power off

immediately and contact your dealer. Water

damage may not be covered under warranty.

Aircraft—FCC regulations prohibit using your

phone on a plane that is in the air. Turn your

phone off or switch it to Airplane Mode before

boarding aircraft.

Resetting the phone

If the screen seems frozen and the keypad does

not respond to keypresses, reset the phone by

completing the following steps:

Vehicles—RF signals may affect improperly

installed or inadequately shielded electronic

systems in motor vehicles. Check with the

manufacturer of the device to determine if it is

adequately shielded from external RF energy.

1. Remove the battery door.

2. Remove and replace the battery.

If the problem persists, return the phone to the

dealer for service.

Accessories

Battery and charger specifications

Charger

Input

Output

Use only Kyocera-approved accessories with

Kyocera phones. Use of any unauthorized

accessories may be dangerous and will

invalidate the phone warranty if said accessories

cause damage or a defect to the phone.

CV90-G2968-01

CV90-G2588-01

CV90-G2589-01

CV90-K0267-01

CV90-K0268-01

CV90-K0269-01

CV90-G2998-01

120VAC 60Hz 7W

5.2VDC 400mA

4.2VDC 0.6A

4.5VDC 1.2A

4.2VDC 0.6A

4.2VDC 500mA

100-240VAC 50/60Hz 0.2A

100-240VAC 50/60Hz 0.3A

100-240VAC 50/60Hz 0.2A

Radio Frequency (RF) energy

Your telephone is a radio transmitter and

receiver. When it is on, it receives and sends out

RF energy. Your service provider’s network

controls the power of the RF signal. This power

level can range from 0.006 to 0.6 watts.

Standard Battery:

CV90-N1020-06: 3.7 V / 900 mAh

Extended Battery:

In August 1996, the U.S. Federal

Communications Commission (FCC) adopted RF

exposure guidelines with safety levels for hand-

held wireless phones. These guidelines are

consistent with the safety standards previously

set by both U.S. and international standards

bodies in the following reports:

CV90-N1070-05: 3.7 V / 1550 mAh

Kyocera Wireless Corp.

10300 Campus Point Drive, San Diego, CA 92121

U.S.A.

•

ANSI C95.1 (American National Standards

Institute, 1992)

NCRP Report 86 (National Council on

Radiation Protection and Measurements, 1986)

Visit us at www.kyocera-wireless.com

ICNIRP (International Commission on

Non-Ionizing Radiation Protection, 1996)

Your phone complies with the standards set by

these reports and the FCC guidelines.

E911 mandates

Where service is available, this handset

complies with the Phase I and Phase II E911

Mandates issued by the FCC.

User Guide for the Slider Jet Phone

CONTENTS

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Using the Camera . . . . . . . . . . . . . . . . . . . . . . . .38

Taking a picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Camera key map . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Recording a video . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1xEV-DO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Getting to know your phone . . . . . . . . . . . . . . . . . . . . .3

Making and Answering Calls . . . . . . . . . . . . . . . 9

Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Silencing an incoming call . . . . . . . . . . . . . . . . . . . . .10

Using the speakerphone . . . . . . . . . . . . . . . . . . . . . . .10

Speed dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Setting up voicemail . . . . . . . . . . . . . . . . . . . . . . . . . .13

Understanding roaming . . . . . . . . . . . . . . . . . . . . . . .15

10 Customizing Your Phone. . . . . . . . . . . . . . . . . .43

Silencing all sounds. . . . . . . . . . . . . . . . . . . . . . . . . . 44

Choosing ringers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Setting sounds for your phone . . . . . . . . . . . . . . . . . . 45

Using shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Personalizing the screen . . . . . . . . . . . . . . . . . . . . . . 47

Creating a secure environment. . . . . . . . . . . . . . . . . . 49

Setting position location. . . . . . . . . . . . . . . . . . . . . . . 52

Storing Contacts . . . . . . . . . . . . . . . . . . . . . . . . 17

Creating a new contact . . . . . . . . . . . . . . . . . . . . . . . .17

Adding a code or extension. . . . . . . . . . . . . . . . . . . . .17

Customizing your contacts . . . . . . . . . . . . . . . . . . . . .18

Editing a contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Erasing a contact . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Sending a vCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Customizing a phone number . . . . . . . . . . . . . . . . . . .19

Finding contact information . . . . . . . . . . . . . . . . . . . .20

11 Sending and Receiving Multimedia

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Sending multimedia messages . . . . . . . . . . . . . . . . . . 53

Receiving multimedia messages. . . . . . . . . . . . . . . . . 54

Viewing multimedia messages . . . . . . . . . . . . . . . . . . 55

12 Using Voice Recognition . . . . . . . . . . . . . . . . . .57

Setting up voice dialing . . . . . . . . . . . . . . . . . . . . . . . 57

Making a call using voice tags . . . . . . . . . . . . . . . . . . 57

Making a call using digit dialing. . . . . . . . . . . . . . . . . 58

Training voice recognition. . . . . . . . . . . . . . . . . . . . . 60

13 Using Tools and Games. . . . . . . . . . . . . . . . . . .61

Voice Memo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Alarm Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Tip Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Games . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Brick Attack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Entering Letters, Numbers,

and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Sending and Receiving Text

Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Sending text messages. . . . . . . . . . . . . . . . . . . . . . . . .24

Retrieving text messages . . . . . . . . . . . . . . . . . . . . . . .28

Customizing message settings . . . . . . . . . . . . . . . . . . .29

Removable Memory Card. . . . . . . . . . . . . . . . . 31

Inserting the Transflash (microSD) card . . . . . . . . . .31

Formatting the Transflash (microSD) card . . . . . . . . .31

Saving files on the card . . . . . . . . . . . . . . . . . . . . . . . .32

Using the Music Player. . . . . . . . . . . . . . . . . . . 34

Playing music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Music Player controls . . . . . . . . . . . . . . . . . . . . . . . . .34

Playback options. . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Viewing details about the playlist. . . . . . . . . . . . . . . . .35

Erasing a song/audio file. . . . . . . . . . . . . . . . . . . . . . .35

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

14 Using Media Gallery . . . . . . . . . . . . . . . . . . . . . .67

Accessing files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

15 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Connecting to the Internet . . . . . . . . . . . . . . . . 36

Using the Web Browser. . . . . . . . . . . . . . . . . . . . . . . .36

Getting Started

To charge the battery:

Installing the battery

1. Connect the

AC adapter to the jack

on the bottom of the

phone.

Your Kyocera phone comes with a removable

lithium ion (LI Ion) battery. Fully charge the

battery before using the phone.

To install the battery:

2. Plug the adapter into a

1. Hold the phone

wall outlet.

face down.

The battery icon in the

upper-right corner of the screen tells you

whether the phone is:

2. Slide the tab at the bottom

of the door up and

remove the battery door.

–

Charging (the icon is animated)

Partially charged

3. Place the battery in the

phone casing with the

Fully charged

metal contacts facing the

right side of the phone.

Recharging the battery

You can safely recharge the battery at any time,

even if it has a partial charge.

4. Replace the battery door

by sliding the notches into

the openings near

Note: To remove the battery, make sure the phone

is powered off.

the top of the phone.

5. Snap the battery door

closed to secure the cover

into place.

Note: If you are using a 400 mA charger with any

of the following part numbers: CV90-G2968-01;

CV90-G2610-02; or CV90-60859-1, please be

aware that this power unit is intended to be

correctly oriented in a vertical or floor

mount position.

Charging the battery

You must have at least a partial charge in the

battery to make or receive calls.

User Guide for the Kyocera Slider Jet Phone

1xEV-DO is an acronym for Evolution Data Only,

and enables download speeds over cell phone

networks of up to 2.4Mb per second. 1xEV-DO is

considered the first 3G, or third generation

wireless standard to be adopted within the US.

Caring for the battery

General safety guidelines

•

Do not take apart, puncture, or short-circuit

the battery.

What this means for phones that have 1xEV-DO

capability is that not only will they be used to

make and receive phone calls and text messages,

but also will be used to quickly access multimedia

content, such as streaming or downloaded audio

or video.

If you have not used the battery for more than

a month, recharge it before using your phone.

Avoid exposing the battery to extreme

temperatures, direct sunlight, or

high humidity.

•

Never dispose of any battery in or near a fire.

It could explode.

Accessing keypad shortcuts

Common causes of battery drain

4-Way navigation key

•

Playing games or using the Web.

Playing music files.

From the home screen, press the Navigation key

in one of four directions to access three

shortcuts and one custom menu (see page 47 for

instructions on setting up your custom menu).

Access your custom menu

Taking pictures and videos with the flash on.

Keeping backlighting on.

Operating in digital mode when far away from

a base station or cell site.

Launch browser

Record voice memo

•

Using data cables or accessories.

Operating when no service is available, or

service is available intermittently.

View recent calls

Your Kyocera phone has a 4-way navigation key

with an OK button ( )at the center. The OK

button has the following functions:

•

High earpiece and ringer volume settings.

Repeating sound, vibration, or lighted alerts.

•

Music Player—Press and hold

Music Player.

to start the

1xEV-DO

1xEV-DO is a standard for wireless broadband

provided by select cell phone carriers.

•

OK key —

acts as a standard OK key that

can be used to select highlighted items.

Getting Started

Getting to know your phone

The phone is shown here in the open position. You must slide your phone open to use the keys on the

lower portion of the phone.

Home screen.

Left softkey accesses menus and functions.

Send/Talk key starts or answers a call. Press once to

activate voice dialing, twice to display the Recent Calls

list, and three times to redial the last number dialed.

Back key erases characters in text entry and returns you

to the previous screen.

Speakerphone key activates the speakerphone and

answers incoming calls.

Keypad for entering numbers, letters, or symbols.

*/Shift key changes the text mode in text entry.

Jack for AC adapter and data cable.

Navigation key scrolls through lists and text entry

fields and accesses shortcuts from the home screen.

OK key selects a menu item or option; Press and

hold for shortcut to Music Player.

Right softkey accesses the Contacts directory and

other menu options.

End/Power key turns the phone on and off, ends

a call or browser session, and returns you to the

home screen.

Internal camera key activates Camera mode. To activate

Camera mode, press and hold to activate the viewfinder

#/Space key enters a space during text entry. Press and

hold to activate or deactivate Silent mode.

0/Next key cycles through word choicesduring text entry.

User Guide for the Kyocera Slider Jet Phone

Antenna does not extend.

Speaker for ringers, speakerphone and music.

External camera key activates Camera mode. To activate

Camera mode, press and hold to activate the viewfinder.

micro SD card slot

Service Indicator Light

Camera flash

Jack for hands-free headset.

Mirror when taking your own picture.

Camera lens

Volume key to raise or lower speaker volume. Press and hold

up or down to activate/deactivate Silent Mode. Press up or

down to silence an incoming call.

Side music button launches the Music Player.

Getting Started

Using menus

The contents of the main menu are as follows:

Recent Calls

Messages

Media Gallery

Tools & Games

Phone Info

All Calls

New Text Msg

New Pic Msg*

Voicemail

InBox

Browser Alerts*

Sent

Camera Pictures

Images

Sounds

Brick AttackTM

Race 21TM

Voice Memo

Scheduler

Alarm Clock

Tip Calculator

Calculator

Platform

Incoming Calls

Outgoing Calls

Missed Calls

Erase Call Lists

Recent Calls Timer

All Calls Timer

Your Number

SW Version

PRL Version

Factory Config

ESN

Videos

Camera

Launches the camera

OutBox*

Technology

Saved

Drafts

Msg Settings

Group Lists*

Erase Messages

Timer

Stopwatch

SID

Browser Info

Icon Key

Settings

Contacts

Silent Mode

Keyguard

Sounds

View All

Add New

Find Name

Speed Dial List

Voice Dial List

Messaging Groups

Business List

Personal List

Information

Web Browser

BREW Apps**

Connects to Internet

Display

Music Player

Convenience

Memory Card

Voice Features

Messaging

Security

Network

Accessories

USB Mode

Displays your music

library (if music files

are saved on an

inserted memory

card)

* Not available on all phones. Check with your service provider.

** Menu name varies by service provider.

In this guide, an arrow → tells you to select an

Accessing menu items (slide open)

option from a menu.

•

From the home screen, press the left softkey

to select Menu.

For example, Menu → Settings means select

Menu, then select the Settings option.

•

Press the right softkey

to select Contacts.

Note: To change the way the menus appear, see

“Choosing a menu view” on page 47 for details.

Press

left, right, up, or down to see

menus and options.

•

Press

to select a menu item.

to back up a menu level.

to return to the home screen.

User Guide for the Kyocera Slider Jet Phone

Performing basic functions

Slide opened or closed

Note: The phone must be powered ON to perform the following functions.

To...

From the home screen...

Press the end key

Turn the phone on

Turn the phone off

Make a call

Press and hold the end key

Press the send/talk key

to initiate voice dialing. Contact must

have voice tag assigned (see page 57).

- or -

From the Contacts menu, select the desired number and press

End a call

Press the end key

Answer a call

Press the send/talk key

Verify your phone number

Adjust volume during a call

Acknowledge an alert

Access menus

Select Menu → Phone Info.

Press

up or down.

Press the send/talk key

Press the left softkey

when you see OK.

once.

Scroll menus

Press

up and down.

Select menus

Highlight a menu or option and press

once.

Access Recent Calls List

Access Browser

Press and hold

down.

left.

Getting Started

Access Custom Menu

Record a Voice Memo

Activate Camera mode

Take a picture

Press and hold

up.

right.

Press and hold the side camera key

Activate Camera mode and press the left softkey

Switch from Camera to

Video mode

From Camera mode, press and hold the side camera key

Record a video

Press and hold the side camera key twice and press the left

softkey

Press

Silence the ringer on an

incoming call

up or down; Press the end key

to answer.

or the left softkey

then the send/talk key

Access Music Player

Press and hold or

Slide open

In addition to the functionality with the slide closed, the following additional methods to access functions

are available with the slide open:

To...

From the home screen...

Make a call

Access voicemail

Take a picture

Enter the number and press the send/talk key

Press and hold

and follow the system prompts.

Press and hold camera key

Capture.

. Focus on the image and select

Record a video

Press and hold camera key

Focus on the image and select Record. To stop recording,

. Select Options → Video Mode.

select Stop.

User Guide for the Kyocera Slider Jet Phone

Understanding screen icons

These icons may appear on your phone’s screen.

The battery is fully charged. The more

black bars, the greater the charge.

1xEV-DO is available.

The phone is operating in IS2000 (1X)

digital mode.

The phone is operating in IS95

digital mode.

The phone is receiving a signal. You can

make and receive calls. Fewer bars

indicate a weaker signal.

The alarm clock is set.

The phone is in privacy mode or is

accessing a secure Web site.

High-speed (3G) data service is

available and active on your phone.

Check with your service provider for

availability.

A call is in progress.

(blinking) The phone is sending high-

speed data.

(blinking) The phone is receiving high-

speed data.

High-speed data service is available, but

the phone is dormant.

The phone is at the home screen. To

access Menu, press the left softkey

The phone is at the home screen. To

access Contacts, press the right

The phone is not receiving a signal. You

cannot make or receive calls.

The phone is roaming outside of its

home service area.

You have a text message.

(

indicates the message is urgent.)

You have a voice message.

You have a voice/text message.

The phone is in camera mode.

Camera flash mode is ready.

Camera timer mode is ready.

Camera zoom mode is ready.

softkey

The phone is set to light up instead

of ring.

The phone is set to vibrate or to vibrate

and then ring.

Position location is set to your service

provider and to emergency services.

Position location is set to emergency

services only.

The phone is in video mode.

Getting Started

MAKING AND ANSWERING CALLS

2. Say the name of the contact when prompted.

Making a call

Make sure you are in an area where a signal can

The phone places the call.

3. Press the end key

once.

be received. Look for the

symbol on the home

screen. The more bars you see in this symbol, the

stronger the signal. If there are no bars, move to

where the signal strength is better.

Ending calls using the slide

You can set the phone to end calls immediately

when you close the slide.

When the phone has been idle for a time, it

changes to power save mode. When you do not

see your home page on your phone’s screen

because it is in power save mode, press any key to

return to normal operating mode.

•

Select Menu → Settings → Convenience →

Close to End → Enabled.

–

Select Disabled to have the phone call

continue when you close the slide.

Slide open

Answering a call

1. Open the slide.

When a call comes in, the phone rings, vibrates,

or lights up, and a dancing phone icon appears.

The phone number of the caller also appears if it

is not restricted. If the number is stored in your

Contacts directory, the contact name appears.

2. Enter the phone number and press the

send/talk key

3. To end the call press the end key

close slide (if “Close to End” is enabled. See

“Ending calls using the slide”).

Slide open

•

Press the send/talk key

incoming call.

to answer the

Slide closed

The voice dialing feature is the only method of

making a call when he slide closed. Voice dialing

requires that a contact be saved with a voice tag.

See page 57.

- or -

•

Press

to answer the incoming call and

turn on the speakerphone.

1. Press the send/talk key

to initiate

Slide closed

Press the send/talk key

Answer Call.

voice dialing.

•

to select

User Guide for the Kyocera Slider Jet Phone

Answering calls using the slide

Redialing a number

•

You can set the phone to answer immediately

when you open the slide. This feature does not

apply to incoming data or fax calls.

To redial a recent call, press the send/talk key

twice to open your Recent Calls list.

Highlight a phone number or name and press

the send/talk key

Tip: To redial the last number called,

received, or missed, press three times.

•

Select Menu → Settings → Convenience →

Open to Answer → Enabled.

–

Select Disabled to have the phone continue

ringing when you open the slide.

Calling a saved number

If you have already saved a phone number, you

can use the Contacts list to find it quickly.

Adjusting the volume during a call

•

To adjust the earpiece volume during a call,

press up or down.

1. From the home screen, press the right softkey

to select Contacts.

Silencing an incoming call

This action silences the current call only. The next

call will ring as normal.

2. Scroll down the list to find the contact you

want to call.

3. Highlight the name and press the send/talk

Note: In the absence of voicemail, this feature

drops the call.

key

to dial the number.

Using the speakerphone

Your Kyocera phone has a built-in speakerphone.

•

Press the end key

or the the left

softkey

- or -

•

To turn on the speaker, open the slide and

press . If you press during an

incoming call alert, you answer the call.

The icon at the top of the phone screen

•

Press the volume key up or down.

To silence the call then answer

Press the end key then press the send/

talk key

•

indicates that the speakerphone is on.

•

To turn off the speakerphone, open the slide

This action silences the current call only. The next

call will ring as normal.

and press

Making and Answering Calls

Note: If you are already on a call and you receive

another call, you cannot place the incoming call

on hold. It will go to voicemail.

Dialing a three-way

conference call*

To dial a three-way conference call, dial the first

1. When a call comes in, press the right softkey

to select Hold Call. The caller will be

placed on hold and will hear your recorded

hold message.

number and press

press again.

, dial the second number,

*May not be available on your phone, check with

your service provider

2. To speak to the caller, select Answer.

- or -

Setting the phone to hold calls

To hang up without speaking to the caller,

select End Call.

The Hold Call feature allows you to place

incoming calls on hold until you are ready to

answer them.

Changing the hold message

Note: This feature will not work if “Open to

Answer” is enabled. See “Answering calls using

the slide” on page 10.

1. Select Menu → Settings →

Convenience → Hold Call →

Re-Record Msg and follow the prompts.

1. Select Menu → Settings →

2. Record the message twice.

Convenience → Hold Call→ Enabled.

3. Select Save or Options (Play, Re-Record,

–

If you have not recorded a hold message,

you will be prompted to record one, such as

“Please hold. I’ll answer in a minute.”

or Exit).

Dealing with missed calls

2. Record the message twice, as prompted.

When you have missed a call, “Missed Call”

appears on your screen unless the caller leaves

a voicemail.

3. Select Save or Options (Play, Re-Record,

or Exit).

The next time a call comes in, you will have the

option of placing it on hold.

•

To clear the screen, press the left softkey

to select OK.

To view details of the call, press the right

Placing a call on hold

softkey

to select Calls then press

You can place a call on hold once you have

enabled this feature.

To return the call, press

to select Calls

then press the send/talk key

User Guide for the Kyocera Slider Jet Phone

Note: If the phone number has been classified as

“secret,” you must enter your four-digit lock code

to view or edit it. For information on the lock

code, see “Changing your lock code” on page 49.

To classify a phone number as secret, see

“Creating a new contact” on page 17.

Setting missed call alerts

You can set an alert to beep every five minutes

after you have missed a call.

1. Select Menu → Settings → Sounds →

Alerts → Missed Call Alert.

2. Select an option and press

Calling recent calls

Viewing recent call details

Slide open

Details on the last 60 calls you made, received, or

missed are stored in the Recent Calls list and are

identified by the following icons:

1. Press

2. Highlight the number you want to call and

press

down.

Outgoing call

Incoming call

Slide closed

Missed call (flashing)

1. Select Menu → Recent Calls →

Outgoing Calls.

Viewing recent calls

2. Highlight the number you want to call and

1. Select Menu → Recent Calls.

2. Select a list: All Calls, Incoming Calls,

press the send/talk key

Outgoing Calls, or Missed Calls.

Erasing recent calls

3. Select a recent call item and press the right

1. Select Menu → Recent Calls →

softkey

to select Options:

Erase Call Lists.

–

Save adds the phone number to the

Contacts list.

Send Msg sends a text message to

the contact.

Send Pict Msg sends a picture message to

the contact.

Erase erases the selected call record.

2. Select an option: All Calls, Incoming Calls,

Outgoing Calls, or Missed Calls.

3. Press the left softkey

to select Yes.

Making and Answering Calls

Using 1-Touch dialing

Speed dialing

To call a contact that has a speed dial location:

Before you can use speed dialing, you must save a

phone number as a contact and assign a speed

dial location to it.

•

From the home screen, press and hold the

speed dialing number. If it is a two-digit

number, press the first digit briefly, then press

and hold the second digit. For example, if the

speed dialing location is 15, press

•

To add a speed dial location to a saved or new

contact, see “Customizing a phone number”

on page 19.

briefly, then press and hold

Using speed dialing

To call a contact that has a speed dial location:

Setting up voicemail

•

From the home screen, enter the one- or two-

digit speed dialing location and press the

Before your phone can receive voicemail

messages, you must set up a password and record

a personal greeting with your service provider.

When you have set up your voicemail, all

unanswered calls to your phone are automatically

transferred to voicemail, even if your phone is in

use or turned off.

send/talk key

1-Touch dialing

1-Touch dialing is the fastest way to speed dial a

contact that has a speed dial location.

1. From the home screen, press and hold

2. Press at the message.

Note: You must (1) enable 1-Touch dialing on

your phone and (2) have a speed dial location

assigned to a contact. See “1-Touch dialing” on

this page.

3. Follow the system prompts to create a

password and record a greeting.

Note: If you are having trouble accessing your

voicemail, contact your service provider.

Enabling 1-Touch dialing

•

Select Menu → Settings → Convenience →

1-Touch Dialing → Enabled.

Checking voicemail messages

When a voice message is received, your screen

displays “New Messages” along with the

symbol at the top of your screen. The symbol

flashes if the message is urgent.

User Guide for the Kyocera Slider Jet Phone

To make or receive regular calls after dialing the

code, you must exit this mode.

If you see “New Messages”

Slide open or closed

1. Press the right softkey

which initiates a call to your voicemail

number.

to select Call,

To exit Emergency mode

When you have completed the emergency call:

1. Press

to select Exit.

2. Follow the prompts to retrieve the message.

To clear the screen without checking messages:

2. Press

again to confirm your choice.

Note: To determine who has access to your

location, see “Setting position location” on

page 52.

•

Press the left softkey

to select Ignore.

If you see only the

symbol

Slide open

Tracking calls

You can track the number and duration of calls

made and received on your phone.

1. Press and hold

to initiate a call to your

voicemail number.

2. Follow the prompts to retrieve the message.

1. Select Menu → Recent Calls.

2. Select a timer:

•

You can set the phone to beep or vibrate every

five minutes to remind you that you have

voicemail. See “Setting message alerts” on

page 46.

–

Recent Calls Timer tracks all calls you have

made and received since you last reset this

timer. To reset this timer to zero, press the

Calling emergency services

right softkey

to select Reset.

–

All Calls Timer tracks all calls you have

made and received. This timer cannot

be reset.

Note: Regardless of your 3-digit emergency code

(911, 111, 999, 000, etc.), your phone operates

as described below.

•

Dial your 3-digit emergency code and

press the send/talk key

Timing your calls

You can set your phone to beep 10 seconds

before each minute passes when you are on a call.

You can call the code even if your phone is locked

or your account is restricted. When you call, your

phone enters Emergency mode. This enables the

emergency service exclusive access to your phone

to call you back, if necessary.

•

Select Menu → Settings → Sounds →

Minute Alert → Enabled.

Making and Answering Calls

Setting an alert for roaming

Receiving data or faxes

You may use this setting if you want the phone to

alert you when you roam outside of your home

service area.

Your phone may be able to receive certain data or

faxes, depending on the system sending the

information. For more information, see page 51.

1. Select Menu → Settings → Network →

Understanding roaming

Roam/Svc Alert.

2. Select an option and press

Controlling network roaming

–

When no svc alerts you with three tones

Depending on services available from your

service provider, you may set the phone to either

digital or analog mode. This is useful if you are in an

area that borders on digital service and the

automatic feature is causing the phone to keep

switching between modes.

decreasing in pitch when service is lost and

three tones increasing in pitch when service

is acquired again.

On roam change alerts you with two

decreasing tones when roaming service is

acquired and three increasing tones when

home area service is acquired again.

On any change alerts you with three

increasing tones if there is a change in

roaming service or three decreasing tones if

the phone loses service.

1. Select Menu → Settings → Network →

Digital/Analog.

2. Select an option and press

–

Automatic automatically switches the phone

between digital and analog.

Analog only sets the phone to work in

analog mode only.

Analog call forces a call into analog mode

for the duration of the next call.

Digital only sets the phone to work in digital

mode only.

Setting the roam ringer

You can set a ringer to indicate when an incoming

call will be subject to roaming charges.

•

Select Menu → Settings → Sounds →

Roam Ringer → Enabled.

User Guide for the Kyocera Slider Jet Phone

Setting Call Guard

You can set the phone to warn you before you

answer or place a call while roaming.

•

Select Menu → Settings → Convenience →

Call Guard → Call Prompt.

–

The phone now emits a distinctive roam ring

to indicate when you are roaming during

calls.

–

To accept or place a call while roaming, you

must press

Note: Call Prompt is disabled when the phone is

in Emergency Mode.

Making and Answering Calls

STORING CONTACTS

Use your phone’s Contacts directory to store

information about a person or company. Each

contact entry can have up to six phone numbers,

two email addresses, two Web addresses, two

street addresses, and a space for notes.

letters for email or Web addresses, see

“Changing modes” on page 22.

Adding a code or extension

When you save the phone number of an

automated service, you may include a pause to

stop dialing, for example, where you would wait

to dial an extension.

Creating a new contact

1. With the slide open, from the home screen,

enter the phone number you want to save,

including the area code.

1. From the home screen, enter the first portion

of the phone number.

2. Press the left softkey

3. Press to select Save New Contact.

4. Enter a name for the contact.

to select Save.

2. Press the right softkey

to select Options.

3. Select a type of pause:

–

Time Pause causes the phone to

stop dialing for two seconds.

–

If you need to learn how to enter letters,

see “Understanding text entry screens” on

page 21.

–

Hard Pause causes the phone to

stop dialing until you select

Options → Release.

–

To add a symbol or smiley to the contact

name, or to change the text entry mode,

4. Enter the remaining numbers.

press the right softkey

5. Press to select Save.

select Options.

5. Either save now or add more contact

information.

–

To save now, press the left softkey

select Save.

–

To enter additional phone numbers, email

and Web addresses, street addresses, or

notes, press

down repeatedly. For

help switching between numbers and

User Guide for the Kyocera Slider Jet Phone

Classifying contacts as Personal

or Business

Customizing your contacts

You can customize each contact in your Contacts

directory by assigning ringers, pictures, and

number types, or by classifying your contacts as

Personal or Business.

1. Press the right softkey

to select Contacts.

2. Highlight a contact and press

3. Highlight the contact name and press the right

softkey to select Options.

Assigning ringers

1. Press the right softkey

2. Highlight a contact and press

3. Highlight the contact name and press the right

softkey to select Options.

to select Contacts.

4. Select Classify.

5. Select Personal or Business and press

Note: To assign Personal or Business ringers,

see “Assigning business and personal ringers” on

page 44.

4. Select Ringer → Assign Ringer.

5. Scroll down the list to hear the different

Assigning number types

ringers and press

to select one.

When you assign a number type, an icon is placed

in front of a contact number to specify the type of

number, such as work, home, or mobile.

Assigning pictures

1. Press the right softkey

to select Contacts.

2. Highlight a contact and press

3. Highlight the contact name and press the right

softkey to select Options.

1. Press the right softkey

2. Highlight a contact and press

3. Highlight the contact number and press the

to select Contacts.

4. Select Picture → Assign Picture → Images.

5. Select Saved Images, Wallpapers, or Caller IDs.

left softkey

4. Press

softkey

to select Edit.

down once and press the right

to select Options.

Note: With mobile PhoneTools for Kyocera,

you can transfer digital pictures to your

phone. To purchase MPT or other

accessories, visit

5. Highlight an option to designate the number

as General, Work, Home, Mobile, Pager, or

Fax and press

www.kyocera-wireless.com/store.

Note: You can enter email address, street address,

URL ,and a note associated with this contact. The

associated icon will appear next to the number in

your Contacts directory and Recent Calls list.

6. Scroll through the list to view your options

and press the left softkey

your contact.

to assign it to

Storing Contacts

3. Press the right softkey

4. Highlight Send as vCard and press

5. Enter a recipient’s phone number and press

the left softkey to select Send.

to select Options.

work

home

mobile

pager

fax

email address

street address

Web page URL

note

Customizing a phone number

1. Press the right softkey

2. Highlight the contact to edit and press

3. Press down to highlight the

contact number.

4. Press the right softkey

5. Highlight an option and press

to select Contacts.

Editing a contact

1. Press the right softkey

to select Contacts.

to select Options.

2. Highlight a contact and press

3. Highlight the contact name or number and

press the left softkey to select Edit.

–

Call to call the contact.

Send Text Msg brings you to the text

4. Enter your changes and press the left softkey

messaging screen.

to select Save.

–

Send Pict Msg brings you to the picture

messaging screen.

Erasing a contact

1. Press the right softkey

to select Contacts.

Add Speed Dial assigns or removes the

speed dial location.

2. Highlight the contact to erase and press

View Number to see the selected phone

number.

3. Select Options.

4. Highlight Erase Contact and press

–

Erase Number erases the number from

the contact.

5. Press the left softkey

to confirm.

Secret makes the number secret so that it

will not appear on the screen until the

lock code is entered. Secret numbers can

be called without a lock code. (For more

information, see “Limiting calls” on

page 50.)

Sending a vCard

You can send contact information as a

text messages.

1. Press the right softkey

2. Highlight the contact to send as a vCard and

press

to select Contacts.

User Guide for the Kyocera Slider Jet Phone

–

Primary Number makes this number the

first one that shows up when you open

the contact.

Add Voice Dial to record a voice tag so you

can call a contact using voice recognition

(VR). For more information, see page 57.

Erase Voice Dial erases the voice tag

associated with the number.

letter of the alphabet.

- or -

Select Menu → Contacts.

2. Select a search method:

–

View All lists all saved contacts.

Find Name locates a specific name. Enter

part of the contact name then select Find.

Speed Dial List, Voice Dial List, Messaging

Groups, Business List, or Personal List

selects a contact from the specified list.

–

Edit Voice Dial records a new voice tag.

6. Enter the new information and follow

the prompts.

3. Highlight a contact and press

To call the contact, highlight the number

and press the send/talk key

7. Select Save, if necessary.

–

Finding contact information

To find a phone number or contact, you can (1)

check the Frequent list, (2) search the Contacts

directory, or (3) use Fast Find.

Setting Fast Find

With Fast Find, you press one or two keys to view

close matches of the number you are looking for.

•

Select Menu → Settings → Convenience →

Checking the Frequent List

Fast Find → Enabled.

From the home screen, select Contacts. The last

15 of your most frequently called contacts appear

when the Frequent List is enabled. Scroll past the

double line to view the All Contacts list.

Using Fast Find

1. From the home screen, press the keys

corresponding to the letters of the name you

want to find. A matching contact or speed dial

entry appears.

To enable the Frequent List setting

•

Select Menu → Settings → Convenience →

Frequent List → Enabled.

2. Press

matching entries.

3. Highlight the name you want then press the

send/talk key to call the number.

down to scroll through

Searching the Contacts directory

1. Select Contacts for a list of all contacts.

To quickly get down the list, enter the first

letter of the contact. The menu skips to that

Storing Contacts

ENTERING LETTERS, NUMBERS, AND SYMBOLS

You can enter letters, numbers, and symbols in

contacts, text messages, and your banner.

Entering numbers

•

To enter a number while in

a number key once.

mode, press

Understanding text entry screens

The current text entry mode (and capitalization

setting, when applicable) are indicated by icons.

To enter a number while in

mode, press and hold a number key until the

number appears on the screen.

capitalization setting

text entry mode

Entering words letter by letter

1. Press a key once for the first letter, twice for

the second letter, and so on. If your phone is

set to Spanish, French, or Portuguese,

accented letters are available.

text entry

fields

characters

remaining

2. Wait for the cursor to move right and enter the

next letter.

Note: To enter a space, press

Text entry modes

There are six text entry modes:

Case change

Entering words quickly

When you press a series of keys using

checks its dictionary of common words and

guesses at the word you are trying to spell.

mode,

Number only

Normal alpha

1. For each letter of the word you want, press the

Rapid Entry

key once. For example, to enter the word

Add Symbol

“any” press

2. If the word doesn’t match what you want,

press to look at other word matches.

3. When you see the word you want, press

→

Add Smiley

Note: The mode you start in depends on the task

you are doing. For example, when entering a

phone number, you’re in number mode. When

entering a name for a contact, you’re in normal

text mode. See “Changing modes” on page 22.

User Guide for the Kyocera Slider Jet Phone

Entering symbols

Changing modes

While entering text, you can enter symbols by

Sometimes you need to change modes. For

pressing

until you see the symbol you want.

example, to enter numbers in an email address

Using this method, you have access to the

following symbols:

while in

mode, enter the numbers, and then change

back to mode to complete the address.

To change text entry modes:

mode, you must change to

@ ?

& : ‘ 1

To access the full set of symbols:

•

Press and hold

until the icon for the

1. From the text entry screen, select Options.

mode you want appears at the top of

the screen.

2. Select

Add Symbol.

3. Press

down to view the list of symbols.

- or -

4. Press the number key corresponding to the

•

Select Options then select a different mode.

symbol you want.

Capitalization settings

You can change capitalization at any time while

Entering smileys

1. From the text entry screen, select Options.

entering text. Simply press

or lower case while in

to choose upper

Normal Alpha mode.

2. Select

Add Smiley.

3. Press

down to view the list of smileys.

4. Press the number key corresponding to the

smiley you want.

Switching default text entry modes

You can change the default text entry mode when

creating a text message. This setting applies only

to the message body screen, not the “To” screen.

1. Select Menu → Messages →

Msg Settings → Default Text.

2. Select Normal Alpha or Rapid Mode.

Entering Letters, Numbers, and Symbols

Quick reference to text entry

This table gives general instructions for entering letters, numbers, and symbols.

To...

Do this...

Enter a letter

Use

mode and press a key until you see the letter you

want. For more information, see page 21.

Use mode and press a key once to enter its number.

For more options, see page 21.

Enter a number

Enter a symbol

Enter a smiley

Press

Use

until you find the symbol you want. See page 22.

mode and press a key once to enter its number.

For more options, see page 22.

Enter a space

Press

Erase a character

Erase all characters

Press and hold

Move the cursor right or left

Move the cursor up or down

Change text entry modes

Capitalize any letter

Press

right or left.

up or down.

Press and hold

mode, press

. Choose

Lowercase any letter

Select soft options on the screen

Press the appropriate key, the left

Press right or left.

or right softkey

Highlight an option at the bottom

of the screen

User Guide for the Kyocera Slider Jet Phone

SENDING AND RECEIVING TEXT MESSAGES

This chapter describes how to send, receive, and

erase text messages from your phone. For

information on voicemail messages, see “Setting

up voicemail” on page 13.

3. Add another recipient if desired:

–

Press the right softkey

to select

Options then select Recent List, Contacts,

or Group Lists.

- or -

Important: The features and menus described in

this chapter may vary depending on services

available in your area. Check with your service

provider for details and possible usage charges.

–

Enter a space or comma after the first

number then enter another recipient

manually.

Note: You can send a message to up to 10

recipients at once. The messages will be sent

one at a time, once to each addressee.

Sending text messages

You can only send text messages to phones that

are capable of receiving them or to an

email address.

4. When you are done entering addresses,

press

twice.

5. Enter the message. To learn how to enter text,

see “Understanding text entry screens” on

page 21.

Creating a text message

1. Select Menu → Messages → New Text Msg.

2. Enter a recipient’s phone number or

- or -

email address:

Add QuickText, symbols, or emoticons to your

message. See “Including prewritten text and

symbols” on page 25 for information.

–

Select Options to access your Recent List,

Contacts, or Group Lists and press

Select a contact and press

Highlight the email or number field and

press . For more about group lists,

6. Press the left softkey

to select Send. See

“Setting sending options” on page 25 for

information about how and when you want the

message to be received.

see “Creating group lists” on page 29.

- or -

–

Enter a new address manually. (To learn

how to enter text, see “Understanding text

entry screens” on page 21.)

Sending and Receiving Text Messages

Select a contact and press

the number field and press

. Highlight

Including prewritten text and

symbols

–

Save Message saves the message in

your Drafts folder. This prevents the

message from being deleted if you have

activated AutoErase and enables you to

send the message to others.

During text entry, you can insert QuickText,

symbols, or emoticons in your message.

1. From the text entry screen, select Options.

2. Select an option and press

–

Insert QuickText: Scroll through the list of

options and press to select one.

–

Save QuickText saves the message you

have just entered as a prewritten message

then returns to the message entry screen

so you can send the message.

–

Add Symbol: Scroll through the list and

press the corresponding number key to

select it.

Settings allows you to choose from the

–

Add Smiley: Scroll through the list and

press the corresponding number key to

select it.

following after pressing

•Set Priority labels the message as

“Urgent.”

3. When you have finished your message, select

Send. See “Setting sending options” for

information about how and when you want the

message to be received.

•Callback Number includes a callback

number with the message to let recipients

know at what number they can call you

back. Select OK to include your own

number or Edit to enter a different

callback number.

Setting sending options

When you are ready to send a message, you have

several options for how and when you want the

message to be received.

•Send Later schedules a time to send

the message.

2. When you have finished setting options, press

1. Once you have completed the message, select

to return to the message window.

Options:

3. Press the left softkey

to select Send.

–

Add Address returns to the “Send To”

screen to add another recipient without

losing the message. Select Options to

access your Recent List, Contacts, or

Adding a signature

The signature you create is included at the end of

all outgoing messages and is counted as

Group Lists and press

User Guide for the Kyocera Slider Jet Phone

characters in your messages; however, it does not

appear in the message creation screen.

Important: Your service provider will charge you

for each message segment.

To create a signature:

When you start a message, the maximum

character limit appears once you are in the

message entry field. This number counts down as

you enter characters, until it reaches 0. If you

continue to enter text after this counter reaches 0,

a message segment may be appended. When you

reach the message size limit, you are prompted to

edit the message or alerted that the message is

being appended.

1. Select Menu → Settings → Messaging →

Signature.

2. Enter your signature in the text field.

3. Select OK to save the setting.

Note: The characters in the signature are

included in the total character count of the

message. See the note under step 5 in “Creating a

text message” on page 24.

* Not available on all phones. Check with your

service provider.

If you cannot send messages

You may not be able to send or receive messages

if your phone’s memory is nearly full, or if digital

service is not available at the time. To free up

memory, erase old messages. See “Erasing

messages” on page 29.

Receiving incoming calls while

creating messages

•

If you don’t wish to answer the call, press the

right softkey to select Ignore. The phone

returns to the message screen.

Understanding appended messages*

capitalization setting

•

To answer the call, press the send/talk key

. Your message is saved to the Drafts

folder. To return to the message, select

Menu → Messages → Drafts. Select the

message then press the left sotrkey to

select Resume.

text entry mode

text entry field

Viewing your sent messages

characters remaining

To save your outgoing messages, you must first

enable Save to Sent.

If you go over the character limit for a single

message, the phone may automatically append an

empty segment to your message to make space.

1. Select Menu → Messages →

Msg Settings → Save to Sent.

Sending and Receiving Text Messages

2. Select an option and press

Viewing failed or pending messages

–

Enabled automatically saves all

successfully sent messages in the

Sent folder.

Failed or pending messages are stored in

your OutBox.

To view your OutBox:

–

Prompt allows you to choose whether or

not to save your message when you send it.

1. Select Menu → Messages → OutBox. A list of

all failed or pending messages appears.

To view successfully sent messages:

2. Scroll through the list of messages and press

1. Select Menu → Messages → Sent.

to read one.

2. Press

up or down through the list of

The message is pending and will be sent

when possible. You can cancel delivery of

the message.

messages. One of the following symbols

appears next to each message:

The scheduled message will be sent at the

scheduled time. You cannot cancel

delivery of the message.

The message cannot be sent

because service is not available. An alert

appears on your phone if the message

cannot be sent.

The scheduled message has been sent and

will be delivered as scheduled. You

cannot cancel delivery of the message.

The message has been received.

The message has been received and

opened. (This symbol may not be

available. Check with your service

provider.)

The message has been sent to more than

one recipient.

The message has never been sent or has

not been sent since it was last modified.

You can cancel delivery of the message.

User Guide for the Kyocera Slider Jet Phone

1. If the text message is long, press

down to

Retrieving text messages

view the entire message.

When a text message is received, your screen

displays “<x>New Messages” with the

symbol.

2. When you are finished, you can Erase the

message or select Options to do the following:

–

Lock Msg to protect the message from

being accidentally deleted.

•

Press the left softkey

highlight the message, and press the left

to select InBox,

softkey

- or -

to select View.

–

Forward the message.

Reply with Copy to reply to the message

with a copy of the original attached.

•

To Ignore the message, press the right

softkey

–

Save Message to save the message.

The symbol flashes if the message is urgent.

Save as QuickText to save the text from the

message as QuickText, which you can

insert into other messages. Graphics and

sound are not saved as part of

QuickText.(For more about QuickText, see

page 30.)

Note: If you receive a new message while you are

reading a message, the one you are reading will

be replaced by the new one. You can find the

older message in the InBox:

•

Select Menu → Messages → InBox.

–

View Sender information.

To view a message later

Block messages from this sender.

1. Select Menu → Messages → InBox. A list of

all your received messages appears.

3. Select Done.

Note: The

symbol indicates that a graphic did

–

indicates an “Urgent” message.

not come through. It may be too large or

incorrectly formatted.

2. Scroll through the list of messages and press

to read one.

Setting message alerts

Reading the message

You can set your phone to alert you of incoming

text messages or pages. For more information,

see “Setting message alerts” on page 46.

The options available to you may vary. Check with

your service provider.

Note: Sounds embedded in text messages will not

play if the phone is set to Silence All mode.

Sending and Receiving Text Messages

3. A message appears: “Erase all messages?”

Erasing messages

It is a good idea to erase old messages to free up

memory in your phone.

Select Yes to erase messages or No to cancel.

Erasing messages automatically

You have the option of erasing text messages and

pages as you send or read them, erasing them one

at a time from the list in the OutBox or InBox, or

erasing them all at once.

Use this setting to have old messages

automatically erased from the InBox when

memory is low.

•

Select Menu → Messages →

Msg Settings → Auto-Erase →

Old InBox Msgs. Older messages will be

erased as new messages are received.

Erasing single messages

1. Select Menu → Messages.

2. Select the type of text message you want to

erase and press

or Saved.

: InBox, OutBox, Sent,

Customizing message settings

To make messaging easier, you can customize

settings for sending and receiving messages.

3. Highlight the message to erase and press

4. Select Options.

Creating group lists

5. Select Erase msg. to erase the message. A

You can create and save a list of multiple

recipients. Your Kyocera phone stores five group

lists with up to 10 recipients per list.

notification appears: “Erase this message?”

6. Select Yes to erase the message.

Note: You can erase a scheduled message from

the OutBox, but you cannot cancel delivery of

the message.

1. Select Menu → Messages → Group Lists →

Create New.

2. Enter a name for the list. For help entering

Erasing all messages

text, see page 21.

1. Select Menu → Messages →

3. Select Next.

Erase Messages.

4. To enter the first phone number or email

2. Select a folder from which to erase all

address, select an option:

messages: InBox, OutBox, Sent, Saved Folder,

Drafts Folder, or All Messages. To erase

messages from all folders, select

All Messages.

–

Recent List to select numbers from your

Recent List.

–

New Address to enter the phone number

or email address manually.

User Guide for the Kyocera Slider Jet Phone

–

Contacts List to select numbers from your

phone book.

3. Enter or edit the text and press the left softkey

to select Done. For help entering text,

see “Understanding text entry screens” on

page 21.

5. Locate the contact number and press

6. Select Options → Recent List or Contacts.

7. Locate the contact number and press

Note: You can also save a message you have

written or received as QuickText. See “Setting

sending options” on page 25 or “Reading the

message” on page 28.

8. When finished, select Done.

9. To send a message to your new group, see

“Sending text messages” on page 24.

Creating and editing prewritten

messages (QuickText)

Your phone comes with prewritten (QuickText)

messages, such as “Please call me,” which you

can insert into the body of a text message. You can

edit these messages and create new ones. Your

phone will store up to 40 QuickText messages,

with up to 100 characters per message.

1. Select Menu → Messages →

Msg Settings → Edit QuickText.

2. To create a new pre-written message,

select New Msg.

- or -

To edit an existing pre-written message,

highlight the message and select Edit.

Sending and Receiving Text Messages

REMOVABLE MEMORY CARD

Your Kyocera phone supports a

Removing the Transflash

(microSD) card

1. Open the Transflash (microSD) cover.

Transflash^TM(microSD^TM) card, a removable

external storage card that, when inserted into the

phone, increases storage capacity.

2. Place your finger on the top of the card and

You can also transfer files stored on your

computer to the Transflash (microSD) card using

a memory card adapter.

press until it pops out.

Note: Replace the card in its case immediately to

avoid damage or loss.

The Transflash (microSD) card supports .mp3,

.aac, and .mp4 file types, up to 512MB.

Formatting the Transflash

(microSD) card

The memory card can be formatted automatically

or manually.

Note: Protected files cannot be saved onto

the card.

Inserting the Transflash

(microSD) card

Automatic

1. Lift the Transflash (microSD) cover up.

When a memory card is used for the first time, it

is automatically formatted.

(See item 17 in the picture on page 4.)

2. Hold the card with the metal contacts facing

up and push the card in the slot until it

clicks into place.

Note: Formatting or reformatting a memory card

erases all data and files that were previously saved

on the Transflash (microSD) card.

3. Close the cover.

1. Insert the Transflash (microSD) card.

(“Inserting the Transflash (microSD) card”

on this page.)

Note: Text messages do not appear on your

phone when the card is in the phone. To set your

phone to exit media mode so that your messages

appear, set the phone to Auto Off.

2. The phone will automatically begin to format

the card and “Card now ready for use.”

appears after completion.

User Guide for the Kyocera Slider Jet Phone

3. Once the Transflash (microSD) card has been

formatted, you can place (drag and drop)

your music files onto the card.

Note: Use only a previously formatted memory

card when loading music files.

Connecting the Memory Card to your

computer

Manual

Manually format your card if the information on

the card is not readable by your phone or if you

are having other technical issues with the card.

1. Insert the Transflash (microSD) card into the

memory card adapter.

2. Place the adapter with the Transflash

(microSD) card in it into the appropriate slot

on your computer.

Note: Formatting or reformatting a card erases all

data and music files that were previously saved on

the Transflash (microSD) card.

- or -

1. Insert the Transflash (microSD) card.

(“Inserting the Transflash (microSD) card”

on page 31.)

If you do not have a slot in your computer,

connect the memory card reader to

your computer and insert the memory card

into the memory card reader.

2. Select Menu → Settings → Memory Card →

Format Card.

3. Locate the Removable Disk drive on

your computer.

3. Press the left softkey

to select Yes and

format the card.

4. The message “Card now ready for use.”

appears after completion.

Saving files on the card

Music files can be put onto the memory card by

using an optional memory card reader for your

computer, inserting the memory card adapter

directly into a computer which has the

appropriate slot, or by using an optional USB

cable and placing the phone into Mass Storage

Mode.

4. Locate the music files to be placed onto the

memory card and “drag and drop” them to

the Removable disk drive.

5. Place music files into the “music” folder

located on the memory card.

Removable Memory Card

11. To properly disconnect the phone from your

computer you need to double click on the

Safely Remove Hardware icon in the System

Tray on your computer. Follow the prompts to

Stop or remove a Mass Storage Device.

Using the USB cable

1. Load the USB Drivers CD onto your computer

and follow the on-screen prompts. (This is

only required during the initial set-up).

2. Plug the USB cable into bottom of the phone.

3. Plug the USB cable into a USB port on

your computer.

12. When you are done placing files onto the

4. On the phone select Menu → Settings →

memory card, press

USB Mode → USB Storage.

5. Your phone will now be 'viewed' by your

computer as a 'Mass Storage Device'.

6. On your computer double click on

My Computer.

7. You will see the Transflash (microSD) card

that has been inserted in the phone as a

Removable Disk drive.

8. Double click on the appropriate Removable

Disk drive.

9. Double click on the music folder.

10. Drag and Drop your music files into the

music folder.

Note: The phone supports the following

music file types: .mp3, .aac, and .mp4.

User Guide for the Kyocera Slider Jet Phone

USING THE MUSIC PLAYER

Use your phone’s Music Player to listen to your

favorite songs or audio files. Store audio files

directly on an external storage card (Transflash

(microSD)) for your own portable music library.

•

Text messages will not interrupt the player;

however, an icon will appear to notify you of

new messages.

Note: For accessories, visit

www.kyocera-wireless.com/store.

Playing music

1. With the slide closed, from the home screen,

Music Player controls

While you are listening to a song/audio file, you

press and hold

- or -

can use the Navigation key

as follows:

With the slide open, select Menu →

Music Player.

Up - View the playlist.

Down - Restart the song.

Left - Play the previous song in the playlist.

The Music Player screen appears.

Note: The Music Player cannot be accessed

until songs (audio files) have been loaded

onto your phone by your service provider or

an external memory card has been inserted

into the Transflash (microSD) slot.

Right - Play the next song in the playlist.

Press

to pause or resume a selected song.

Playback options

Shuffle

2. Highlight a song and press

or select Play.

Note: Shuffle is inactive if there are fewer than

Notes:

three song/audio filess.

•

When the card is in your phone, the audio

filess on the card appear in the Media

Gallery menu.

1. Select Menu → Music Player.

2. Press the right softkey

to select Options.

Incoming calls, Scheduler events, and the

alarm clock will interrupt the Music Player. An

interrupted song will begin again at the point

it left off with the press of a softkey.

3. Select Settings → Shuffle On. The Shuffle

icon appears.

–

This option changes to Shuffle Off if

Shuffle On has already been selected.

Using the Music Player

Repeat

Erasing a song/audio file

You can erase an audio file from the card using

the phone.

1. Select Menu → Music Player.

2. Press the right softkey

to select Options.

1. Highlight a song/audio file in the playlist.

3. Select Settings → Repeat On. The Repeat

icon appears.

2. Select Options → Erase song → Yes.

–

This option changes to Repeat Off if

Repeat On has already been selected.

Troubleshooting

Scenario: audio file is not playing

Auto Off

Try renaming the file on your PC, removing any

special characters, spaces, and limiting the length

to 30 characters.

The phone exits the Music Player after it has been

paused or stopped for a selected amount of time if

the Auto Off feature is enabled.

If the file still does not play:

1. Select Menu → Music Player.

•

The file type may not be supported.

2. Press the right softkey

to select Options.

The file may be DRM (digital rights

management) protected.

3. Select Auto Off.

4. Select an option and press

: 10 minutes,

•

The file may be corrupted.

20 minutes, or Off.

Scenario: Audio is choppy

Viewing details about the

playlist

•

The file may be corrupted, but the audio still

plays. Check your file for corruption.

To view the total number of audio files and the

amount of memory available on the phone and

the card:

•

While viewing the playlist, select Options →

Playlist Details.

User Guide for the Kyocera Slider Jet Phone

CONNECTING TO THE INTERNET

–

An underline and an arrow indicate that

Using the Web Browser

there is more text. Press

more text. Press

down to view

to return to the

You can use your phone to browse the Internet if

you have obtained phone Internet services from

your service provider and if over-the-air Internet

access is available in your area.

previous screen.

To choose a site, highlight it and press

to select Go.

Note: You cannot receive incoming calls while

you are using Web Browser.

4. When you have finished using the Internet,

press the end key

Web Browser.

to exit the

Launching the Web Browser

1. Select Menu → Web Browser.

Using the Web menu options

A message about airtime fees appears every

time you start the browser.

The following options may appear on your screen:

•

Home returns you to the main Web Browser

window, or home page.

For more information about how airtime is

charged, contact your service provider.

Mark Site saves the current location as a

bookmark for easy access.

2. Press the left softkey

to continue.

If this is the first time you have connected to

the Internet, a message informs you that

security is not yet enabled for your

Web Browser.

Bookmarks displays a list of your saved

Web sites.

Setup gives you options for changing how

information is displayed.

3. Press

to select Yes to enable security.

–

Show URL displays the entire URL.

When you are connected, a browser home

page appears. It has a list of bookmarks and

some Web menu options at the bottom of

the screen.

About Openwave displays information

about your Web Browser version.

–

Encryption should not be used unless you

are instructed to do so by your

service provider.

–

appears in a secure session.

Connecting to the Internet

–

UP.Link selects a different browser server.

You can use this option if you have more

than one Web Browser account.

Restart restarts the Web Browser.

Searching for a Web site

How you search for a Web site depends on

your service provider. For more information,

contact your service provider.

Going to a bookmarked site

1. Select Menu → Web Browser. If you see a

message prompt, press

to continue.

2. From your Web home page, select

Bookmarks. A list of bookmarks appears.

3. Enter the number corresponding to the

bookmark you want and press

Checking Net alerts

Alerts received from a Web site are sent to your

Browser Alerts inbox.

1. Select Menu → Messages → Browser Alerts.

This action launches the browser inbox.

2. Press

to accept browser fees.

3. Select an alert and follow the prompts.

User Guide for the Kyocera Slider Jet Phone

USING THE CAMERA

With the camera open:

Tips before operating

your camera

•

Press and hold

viewfinder.

to activate the camera

•

While the camera is active, the home screen

acts as the viewfinder.

•

Select Options → Video Mode to switch to

video mode.

•

If you get a “Low memory” error, check and

adjust your resolution and quality

- or -

compression settings. See “Setting up the

camera for photos” on this page.

–

Select Menu → Camera to activate

the camera.

•

You can only activate the camera if you are not

on an active call or browsing files in the

Media Gallery.

–

Select Options → Video Mode to switch to

video mode.

Setting up the camera for

photos

If there is no activity within 45 seconds after

you turn your camera on, the camera quits

and returns to the previous launch point.

1. With the slide open, select Menu →

Menu settings and options can only be

accessed when the camera is active.

Camera → Options.

2. Press

to select Settings.

3. Highlight an option and press

Accessing camera and

video modes

The camera can be used with the slide open

or closed.

–

Flash options are On, Off, or Automatic.

Resolution options are 640 x 480,

320 x 240 (best for sending to email),

and 160 x 120.

With the camera open or closed:

–

Low Light Mode brightens the picture for

•

Press and hold

viewfinder.

to activate camera

low light environments.

•

Press

until you hear two beeps to activate

video mode.

Using the Camera

–

Self Timer options are Off (default) or 3,

5, or 10 second pauses. When set, the

camera beeps from 3 seconds down to the

time the shutter snaps the picture

automatically. Self Timer is not available

when Multishot mode is activated.

Restoring camera menu settings

The following settings revert to the default

setting each time you enter and exit the

camera application:

•

Low Light Mode, Self Timer, MultiShot,

Viewfinder.

Multishot allows you to take up to six

multiple pictures while the camera key is

pressed and held. A tone will play each

time a picture is taken. A second tone will

play when the final picture is taken.

The following settings remain at the setting

you selected each time you enter and exit the

camera application:

•

Flash, Resolution, Shutter Sound, White

Balance, Quality, LED, and Save Location.

–

Shutter Sound sets the sound used when

the camera takes a picture.

Menu options for camera mode

1. Press

White Balance allows the camera to adjust

for different lighting. Options are

Automatic, Fluorescent, Incandescent,

or Daylight.

to activate camera mode.

2. Select Options.

3. Press

up or down to scroll through the

options on the vertical menu bar:

–

Quality sets the picture compression. The

higher the compression, the better the

detail of the picture (higher pixel rate).

Options are Low, Medium, or High

(default). When set to High, the picture

file size is larger, using more memory.

–

Settings displays available camera settings

you may set up prior to taking a picture.

Video Mode toggles between video and

camera modes.

Brightness allows you to adjust the

brightness of the image in the home

screen LCD.

–

LED flashes a light to indicate a picture

has been taken. Options are On (default)

and Off.

–

Camera Pictures displays all pictures

taken and stored.

–

Viewfinder options are Fullscreen

and Actual.

Last Picture displays the most recently

Save Location options are Save to Card

and Save to Phone.

taken picture.

User Guide for the Kyocera Slider Jet Phone

–

Frames allows you to add a frame or a

stamp to your picture. A frame or stamp

cannot be removed once it has been used

in a picture.

Taking a picture

Slide open or closed

1. Select Menu → Camera.

Note: The picture resolution changes to

160 x 120 while taking pictures with frames.

The resolution returns to the original setting

once Frames is disabled.

2. Focus on the image using the phone’s display

as the viewfinder.

Tip: Press

up or down to zoom in or

zoom out if the resolution is set to less than

640 x 480.

Camera mode indicators

and icons

The camera mode displays the following onscreen

indicators and icons:

3. Take the picture using one of two methods:

–

Press

or the left softkey

4. Press the left softkey

to select Send or

the right softkey

to select Erase.

Icon

Description

5. Press the end key

when finished

taking pictures.

Flash on

Camera mode

Video mode

Camera key map

Slide open or closed

Key

Camera

Menu Screen

Top right hand

Number of snapshots

corner numbers remaining

Left softkey -

Select Capture

to take picture

Select OK.

Zoom level

Right softkey - Cancel, dismisses menu

Select Options

Bottom left

hand numbers

Resolution setting

Zoom in

Scroll menu options right

Multishot

Self Timer

Down Zoom out

Scrolls menu options left

Takes picture Select menu option

Using the Camera

Setting up the video camera

Menu settings can only be accessed when the

camera mode is activated.

Recording a video

When you begin recording, a tone sounds, the

video record icon blinks, and a “Recording”

indicator with a timer progress bar displays. A

tone sounds when the video stops recording.

1. Select Menu → Camera → Options.

2. Press

down to select Video Mode and

press

Slide open or closed

1. Select Menu → Camera → Options.

Menu options for video mode

2. Scroll down using

to select the Video

1. With the phone set to Video Mode select

Options. Refer to “Setting up the video

camera” on page 41 for instructions.

Mode option.

3. Focus on the image and press

select Record.

2. Press

up or down to scroll through the

4. If you want to pause the recording, press

the right softkey to select Pause. To

continue recording, press the right softkey

again to select Resume.

vertical menu bar and choose an option:

–

Settings allows you to change your

camera settings. White Balance, Quality,

LED, Recording light (turns on the flash as

a steady light for videos) Save Location

(phone/card).

5. When finished recording, press the left softkey

to select Stop.

6. The recorded video is immediately saved to

–

Camera toggles between video and

camera modes.

Media Gallery → Videos → Video Album.

7. Press

when finished

Brightness allows you to adjust the

brightness of the image in the home

screen LCD.

taking videos.

–

Video Album displays all the videos

recorded and stored.

Last Video plays the most recently

recorded video.

User Guide for the Kyocera Slider Jet Phone

Video key map

Slide open or closed

Key

Video Camera Function Menu

Function

Left softkey - “Record” – “OK” –

starts recording toggle

(plays a tone)

“Stop” – stops recording

toggle (plays a tone)

selects option

Right softkey - “Options” – “Cancel” –

while not recording

“Pause/Resume” – pauses

and resumes recording

toggle

dismisses

When not recording, goes Dismisses

back to the last function.

menu options

While recording, stops

recording.

End key – Exit to idle

when not recording.

Exit to idle

Using the Camera

10 CUSTOMIZING YOUR PHONE

The contents of the Settings menu are as follows.

Silent Mode

Vibrate Only

Display

My Banner

Voice Features

Add Voice Dial

Network

Data/Fax Calls

Vibe then Ring

Lights Only

Normal Sounds

Main Menu View

Color Themes

Wallpaper

Screen Saver

Backlighting

Auto-Hyphen

Language

Time/Date

Contrast

Brightness

Erase Voice Dial

Voice Training

Voice Wake-Up

Voice Answer

Expert Mode

Privacy Alert*

Voice Privacy*

Set Phone Line*

Roam/Svc Alert

Roam Option

Digital/Analog

Location

Keyguard

Guard on Close

Disabled

Messaging

Alerts

Signature

Edit QuickText

Auto Retrieve*

Callback Number

Save to Sent

Auto-Erase

Default Text

Voicemail Number

Sounds

Ringer Volume

Ringer Type

Business Ringer

Personal Ringer

Roam Ringer

Alerts

Accessories

Pwr Backlighting

Headset Ringing

Auto-Answer

Com Port Speed

TTY Device

Convenience

Airplane Mode

Open to Answer

Close to End

Fast Find

Slide Open

Slide Closed

USB Mode

USB Storage

Frequent List

Hold Call

Pwr On/Off Sound

Key Volume

COM Mode

Security

Lock Phone

1-Touch Dialing

Web Prompt

Call Guard

Key Length

Limit Calls

Smart Sound

Minute Alert

Earpiece Volume

Spkrphone Volume

New Lock Code

Erase Contacts

Emergency Numbers

Memory Card

Items to Save

Format Card

* Not available on all phones. Check with your service provider.

User Guide for the Kyocera Slider Jet Phone

Shortcut to Vibrate Only mode

Silencing all sounds

•

With slide open, press and hold

Your phone is set to make sounds when you

receive calls, press keys, navigate through menus,

and receive alerts (such as new messages).

With slide closed, press and hold

down.

You can silence all sounds and set the phone to

vibrate or light up when you receive calls

and alerts.

Turning sounds back on

•

With slide open, press and hold

With slide closed, press and hold

up.

Setting the phone to vibrate or

light up

Choosing ringers

Your Kyocera phone has multiple ringers you can

choose to use for incoming calls.

1. Select Menu → Settings → Silent Mode.

2. Choose an option and press

1. Select Menu → Settings → Sounds →

–

Vibrate Only: The phone vibrates for the

duration of the incoming call or other

alerts. appears.

Ringer Type.

2. Scroll down the list to hear the different rings

and press

to select one.

–

Vibe then Ring: The phone vibrates for the

first 10 seconds and then ring for the

remainder of the incoming call alert.

appears.

Note: Downloaded ringers are added to the end

of the standard list of ringers.

Assigning business and

personal ringers

–

Lights Only: The phone lights up for the

duration of the incoming call or other

alerts. appears.

You can assign ringers to contacts classified as

Business or Personal in your Contacts directory.

Normal Sounds: The phone rings for the

incoming call or alert (in effect, returns

phone to a non-silent mode).

Note: To classify a contact as Business or

Personal, see page 17.

Note: The phone will ring when it is attached to

an external power source (such as a charger),

even if all sounds have been silenced.

1. Select Menu → Settings → Sounds.

2. Ηighlight Business Ringer or Personal Ringer

and press

3. Select a ringer and press

Customizing Your Phone

Setting sounds for your phone

Adjusting volume

You can adjust the earpiece, speakerphone, and

ringer volume as well as key tones.

You can set your phone to sound tones when you

open and close the slide and when you turn the

phone on and off. Sounds will not occur during

an incoming call, if you are in a call, or if a

headset or hands-free car kit is attached to

your phone.

Adjusting the earpiece volume

To adjust the earpiece volume manually during a

call, press

up or down.

To set the earpiece volume:

Set sound when slide opens

1. Select Menu → Settings → Sounds →

Slide Open.

Earpiece Volume.

2. Press

right to increase the volume, or left

2. Scroll through the list to hear the sounds and

to decrease the volume.

press

to select one.

3. Press the left softkey

to select Save.

Set sound when slide closes

Using smart sound

1. Select Menu → Settings → Sounds →

Slide Closed.

You can set a baseline volume that the phone uses

to automatically adjust the earpiece volume when

there is a change in the amount of noise around

you or the caller’s voice.

2. Scroll through the list to hear the sounds and

press

to select one.

•

Select Menu → Settings → Sounds →

Smart Sound→ Enabled.

Set sound when phone powers

on or off

•

Select Menu → Settings → Sounds →

Adjusting the ringer volume

Pwr On/Off Sound → Enabled.

1. Select Menu → Settings → Sounds →

–

To deselect this sound, select Disabled.

Ringer Volume.

2. Press

to decrease the volume.

3. Press the left softkey

right to increase the volume, or left

to select Save.

User Guide for the Kyocera Slider Jet Phone

2. Select the type of alert: Message Alert,

Page Alert, Voicemail Alert, or

Missed Call Alert.

Adjusting speakerphone volume

1. Select Menu → Settings → Sounds →

Spkrphone Volume.

3. Press

to select an option:

2. Press

to decrease the volume.

3. Press the left softkey

right to increase the volume, or left

–

Vibrate, Beep, Freeway, Game, Bloop,

Winner, Zilofon sets the phone to alert you

once when a new message is received.

to select Save.

Adjusting key tone volume

–

Vibrate & Remind, Beep & Remind, Fwy &

Remind, Game & Remind, Bloop &

You can change the volume of the tones the phone

makes when you press the keys.

Remind, Winner & Remind, Zilofon &

Remind sets the phone to notify you once

when a new message is received and then

notify you again every five minutes. To stop

1. Select Menu → Settings → Sounds →

Key Volume.

2. Press

right to increase the volume, or left

a reminder alert, press

to decrease the volume.

select Ignore.

3. Press the left softkey

to select Save.

–

Disabled turns off message alerts.

Setting key length

Using shortcuts

From the home screen, press

directions to access three shortcuts and one

custom menu.

You can change the duration of the tones the

phone makes when you press the keys.

in one of four

1. Select Menu → Settings → Sounds →

Key Length.

Up: Access your Custom Menu

Down: Access Recent Calls

2. Choose Normal or Long and press

Left: Launch Web Browser

Right: Record Voice Memo

W Press and hold to start Music Player

Setting message alerts

You can choose how you want be alerted of

incoming voicemail, pages, or text messages.

1. Select Menu → Settings → Messaging →

Alerts.

Customizing Your Phone

2. Press the right softkey

to select Edit.

Creating and updating your

custom menu

3. Press

to clear the screen.

4. Enter your new text.

5. Press the left softkey

You can create a custom menu that contains your

favorite features. After you set up your menu,

to select Save.

simply press and hold

up to access it.

Choosing a menu view

1. Press and hold

up to launch

Three menu views are available: Graphic, List,

and Wheel.

Custom Menu.

2. Press

to select Manage List.

1. Select Menu → Settings → Display →

3. Scroll through the available options and press

Main Menu View.

to select or deselect options.

2. Select an option and press

–

You may select more than one feature.

Items appear in alphabetical order in

the menu.

–

Graphic displays icons of each menu item,

with its name at the bottom of the screen.

–

List displays a list of each menu item.

4. Highlight Save Changes at the top of the list

and press

Wheel displays a rotating graphic image of

the menu items.

Choosing a different language

Your phone may display alternative languages.

3. Press the end key

to return to the home

screen. The next time you select Menu, you

will see the menu view you selected.

1. Select Menu → Settings → Display →

Language.

Adjusting the backlighting

2. Select a language and press

Your screen lights up while you are in a call or

when you press a key on the keypad. However,

you can set the length of time that bright

backlighting remains on.

Personalizing the screen

Changing your banner

1. Select Menu → Settings → Display →

The banner is the personal label for your phone.

It appears on the home screen above the time and

date. The banner can be up to 14 characters long.

Backlighting → Duration.

1. Select Menu → Settings → Display →

My Banner.

User Guide for the Kyocera Slider Jet Phone

2. Select an option and press

Tip: Use the power backlighting as a night light

when traveling.

–

7 seconds, 15 seconds, or 30 seconds—

(Default) Turn backlighting on for 7, 15,

or 30 seconds after your last keypress.

1. Select Menu → Settings → Accessories →

Pwr Backlighting.

–

7 sec. & in call, 15 sec. & in call, or 30 sec.

& in call—Turn backlighting on for the

duration of a call, and for 7, 15, or 30

seconds after your last keypress.

2. Select Always On to keep backlighting on.

Note: The battery charges more slowly when

power backlighting is on.

Changing the display contrast

Note: The “in call” settings drain the battery

more quickly.

1. Select Menu → Settings → Display →

Contrast.

Using Power Save Mode

2. Press

left or right to adjust the contrast

You can conserve battery life by activating Power

Save mode to dim the backlight set in the

procedure above. The backlighting appears for

the selected duration but is less bright than with

Power Save off.

and select Save.

Setting numbers to auto-hyphenate

Auto-hyphenation, when enabled, automatically

inserts hyphens into your phone numbers to be

consistent with the U.S. dialing plan.

•

Select Menu → Settings → Display →

Backlighting → Pwr Save Mode → On.

For example, 1-222-333-4444.

•

Select Menu → Settings → Display →

Setting power backlighting

Auto-Hyphen → Enabled.

You can set backlighting to remain on when an

external power source, such as the AC adapter, is

used with the phone.

Selecting a screensaver

Screen savers appear on the home screen when

the slide is open or closed and are activated 10

seconds after the last keypress. Incoming calls

and alerts override screen savers.

Note: Power backlighting may not be

available with the optional desktop charger

or other accessories.

1. Select Menu → Settings → Display →

Screensaver.

2. Highlight a screensaver and press

. The

image displays.

Customizing Your Phone

3. Press the left softkey

to assign the

Creating a secure environment

screen saver.

This section describes all the features involved in

securing your phone and preventing access to

personal information. All security features are

shielded by a four-digit lock code.

4. Press the end key

to return to the home

screen and wait 10 seconds to view the screen

saver you chose.

Note: Downloaded screen savers are added to

the end of the list.

Changing your lock code

The lock code is typically 0000 or the last 4 digits

of your phone number.

Selecting wallpaper

1. Select Menu → Settings → Security.

Wallpaper appears on the home screen.

2. Enter your four-digit lock code.

1. Select Menu → Settings → Display →

Wallpaper.

3. Select New Lock Code. A message appears:

“Change Code?”

2. Highlight a wallpaper design and press

4. Press the left softkey

to select Yes and

3. Select Assign to save your selection.

enter a new four-digit code.

4. Press the end key

to return to the

5. Enter your new lock code again.

home screen.

Locking your phone

Selecting a color theme

When your phone is locked, you can call only

emergency numbers or your service provider’s

number. You can still receive incoming calls.

You can select a color theme for the display

background of your phone.

1. Select Menu → Settings → Display →

1. Select Menu → Settings → Security.

2. Enter your four-digit lock code.

3. Select Lock Phone.

Color Themes.

2. Scroll through the options to view the color

themes and press to select one.

4. Highlight an option:

Choosing a different time/date format

–

Never does not lock the phone.

1. Select Menu → Settings → Display →

On power up locks the phone every time

Time/Date.

you turn it on.

2. Highlight an option and press

–

Now locks the phone immediately.

5. Press

User Guide for the Kyocera Slider Jet Phone

Unlocking the phone

Limiting calls

1. From the home screen, press the left softkey

You can limit the calls that can be made from your

phone to emergency numbers, your contacts, and

your service provider’s numbers.

to select Unlock.

2. Enter your four-digit lock code.

1. Select Menu → Settings → Security.

2. Enter your four-digit lock code.

3. Select Limit Calls.

Designating emergency numbers

The emergency numbers feature allows you to

specify three personal phone numbers that can be

called when the phone is locked.

4. Choose an option and press

–

No Limit limits no calls.

1. Select Menu → Settings → Security.

2. Enter your four-digit lock code.

3. Select Emergency Numbers.

4. Select an Unassigned slot.

Limit Outgoing calls only. Incoming calls

can still be received and answered.

–

Limit All calls, both incoming

and outgoing.

5. Enter the phone number, including the area

code. Do not enter 1 before the area code.

Erasing all contacts

6. Press the left softkey

Notes:

to select Done.

You can erase all entries from your

Contacts directory.

•

You can view these numbers only when they’re

being entered for the first time.

1. Select Menu → Settings → Security.

2. Enter your four-digit lock code.

3. Select Erase Contacts.

•

You cannot edit these numbers.

To make a call to an emergency number from

a locked phone, you must dial the number

(including area code) exactly as it was stored

in Emergency Numbers.

4. Select Yes to erase all contacts. A message

appears: “Erase ALL Contacts?”

5. Press the left softkey

to select Yes to

erase all contacts.

Customizing Your Phone

Note: There may be a higher charge for making

calls using high-speed data in areas where 1X

service is available. Check with your service

provider for details.

Network settings

Switching between phone lines

Your phone can have two service accounts, or

phone lines, associated with it. Each phone line

has its own phone number.

Setting the phone to receive data

or faxes

When you are using one line, you cannot receive

calls from the other. It would be as if the phone

were “off” for that number. Your voicemail,

however, will still take messages. All contacts and

settings are shared for both lines.

Your phone may be able to receive certain data or

faxes, depending on the system sending the

information. You cannot receive voice calls while

the phone is in data/fax mode.

To receive data or faxes, you must connect the

phone to a laptop or PC and switch the phone

from voice mode to data/fax mode.

Note: You must first establish a second phone

line with your service provider. Once established,

a second phone number becomes available in the

menu for selection:

Note: To purchase a cable, call 800-349-4188

(U.S.A. only), 858-882-1410, or visit

www.kyocera-wireless.com/store.

1. Select Menu → Settings → Network →

Set Phone Line.

1. Connect the phone to the laptop or PC.

2. Select one of the two lines and press

2. Set the Com speed.

Data Settings

3. Select Menu → Settings → Network →

Data/Fax Calls.

Setting Com port speed

4. Scroll through the list and press

to select

The Com Speed sets the data rate at which your

phone connects to a laptop or PC, or at which it

sends and receives over-the-air text messages.

an option:

–

Voice only allows only voice calls.

Fax, next call or Data, next call sets the

phone to fax mode or data mode for the

next incoming call or the next 10 minutes.

1. Select Menu → Settings → Accessories →

Com Port Speed.

2. Select the speed. The options are: 19.2 kbps,

–

Fax, until off or Data, until off forces the

phone into fax mode or data mode until

the phone is turned off.

115.2 kbps (default), 230.4 kbps, and Other.

User Guide for the Kyocera Slider Jet Phone

Note: You cannot receive voice calls while the

phone is in data/fax mode.

–

911 Only (default) shares your position

information only with emergency services

when you call your 3-digit emergency

code (911, 000, 111, etc.).

Connecting to a TTY/TDD device

You can connect the phone to a TTY device for the

hearing impaired.

Location On shares your position

information with your service

provider’s network, in addition to

emergency services.

Note: Enable TTY only when using the phone with

a TTY device.

1. Connect the TTY device to the phone.

2. Enter

your keypad.

from

3. Press the left softkey

to select the

TTY option.

4. Close the Information window by pressing the

left softkey to select OK.

5. Highlight TTY On and press

Setting position location

This setting allows you to share your location

information with network services other than

emergency services (For example: 911, 111, 999,

and 000) in markets where service has

been implemented.

Note: This feature works only when your phone is

in digital mode. You do not have the option of

turning off the locator to emergency services.

1. Select Menu → Settings → Network →

Location.

2. Select 911 Only or Location On.

Customizing Your Phone

11 SENDING AND RECEIVING MULTIMEDIA MESSAGES

–

Press the right softkey

Options. Then select Recent List,

Contacts, or Group Lists.

to select

Sending multimedia messages

You can only send multimedia messages to

phones that are capable of receiving them or to

email addresses. For details, check with your

service provider.

Note: You can send one multimedia message

to a maximum of 10 recipients.

4. Press

twice to enter a “CC” recipient.

twice to enter a “BCC” recipient

twice to enter the Subject. Choose a

Note: The multimedia messages feature is not

available on all phones. Check with your

service provider.

5. Press

6. Press

method:

Multimedia messages have a predetermined

character and file size limit. When you reach the

character and file size limit for a single

multimedia message, you must edit the message

to meet the size limitation.

–

Enter the subject text manually, or

Press the right softkey

select Options.

7. Press

Text field.

8. Press

twice once to enter text in the

twice to enter the Image/Video field.

Creating a multimedia message

1. Select Menu → Messages → New Pic Msg.

2. Enter the recipient’s phone number or email

Note: You may add only one picture or one

video per multimedia message.

address in the To field.

9. Press the right softkey

to select Options.

–

Press the right softkey

Options. Then select Recent List,

to select

Select an option:

•

Take Picture to instantly take a new photo and

attach it to your message.

Contacts, or Group Lists.

3. To add additional recipients:

Record Video to instantly take a new video and

attach it to your message.

–

Enter a space or comma after the first

phone number or email address, then

enter another recipient manually, or

User Guide for the Kyocera Slider Jet Phone

•

Media Gallery to access all picture and video

files in the phone:

–

Preview Msg. plays your multimedia

message prior to sending.

–

Camera Pictures displays your photos

Save Message allows you to save your

multimedia message to the Drafts folder

and send it later.

taken in a table/thumbnail view.

• Highlight a photo to add to the

multimedia message. Press the left

–

Add Address allows you to add additional

addresses to your multimedia message

prior to sending it.

softkey

to choose Select.

–

Images displays stored images on

the phone.

Message Priority allows you to send your

multimedia message with Normal or

Urgent priority.

Videos displays stored videos on

the phone.

12. Press the left softkey

to select Send. This

10. Press

press the right softkey

Options. Choose:

down to enter the Sound field and

will send your multimedia message.

to select

Receiving multimedia messages

•

Record Sound to instantly record a new sound

There are two settings for receiving a multimedia

message on your phone: automatic download

(default) or prompt before download.

and attach it to your message.

•

Media Gallery to display a list of categories

that contain saved or downloaded sounds and

voice memos.

To activate Prompt mode

–

Highlight Saved Sounds.

1. Select Menu → Messages → Msg Settings.

Press the left softkey

to select Open.

2. Press

and press

3. Press

then press

down to select Auto Retrieve

–

Highlight a sound to add to the multimedia

message. Press the left softkey

choose Select.

down and select Disabled,

Note: You may add only one new or stored

sound per multimedia message sent.

Downloading multimedia messages

11. Before sending your message, press the right

softkey to select additional

Options. Choose:

When a multimedia message is received, it is

automatically downloaded onto your phone

unless you change the setting to Disabled as

described above.

Sending and Receiving Multimedia Messages

Automatic Downloading

Viewing multimedia messages

When a new multimedia message arrives, “New

Message(s)” appears along with the text

“Message Received. View now?”

When you receive a multimedia message, a

appears on your phone’s screen and remains until

all messages are viewed. The message is stored in

the InBox until the full message has been

received, regardless of the auto receive or

prompt setting.

Note: If a multimedia message is received during

a call, then the phone screen displays the alert

“New Message(s)” after the call ends.

1. Press the left softkey

multimedia message. If the message is long,

press down to view the entire

to View the

–

To View the multimedia message, press the

left softkey

To view Later, press the right softkey

–

multimedia message.

Prompt before download

2. Press the right softkey

to select Options.

If the phone is set to prompt before downloading,

when the message arrives “New Message(s)”

along with the question “Retrieve Now?”displays.

Press

down to highlight additional

options for the multimedia message (options

vary according to selection):

Note: The options available to you may vary.

Check with your service provider.

Note: If a multimedia message is received during

a call, then the phone downloads the message

approximately one minute after the last key

is pressed.

–

Mute to silence the message.

Erase Msg allows you to delete the

•

To View the multimedia message, press the left

softkey

Press the right softkey

Retrieve Later or Erase

currently displayed multimedia message.

–

Forward launches the message creation

screen, allowing you to forward the

multimedia message. The original address

will not be shown, nor will the graphic,

sound, and text fields.

•

to select Options:

–

Lock Msg to avoid accidentally erasing it.

Message Info displays multimedia

message information (priority, sender,

subject, time sent and received, and

message size).

User Guide for the Kyocera Slider Jet Phone

–

Play Video plays the video in the

multimedia message.

Replay plays the multimedia message

again from the beginning.

–

Done exits the multimedia message.

Call initiates call to sender of

multimedia message.

–

Save Picture saves the currently

viewed picture embedded in the

multimedia message.

–

Save Video saves the video embedded in

the multimedia message.

Save Sound saves the current sound

embedded in the multimedia message.

Save Address extracts email addresses,

phone numbers, and/or URLs from the

sender info and multimedia message body.

–

Save as QuickText saves the text in the

multimedia message to the QuickText list.

Save Message saves the multimedia

message to the Saved Folder on the phone.

3. When you are finished viewing the

multimedia message, select Reply or press

the end key

Sending and Receiving Multimedia Messages

12 USING VOICE RECOGNITION

Voice recognition allows you to make and

answer calls by speaking commands into the

phone’s microphone.

3. Highlight the phone number and

select Options.

4. Select Edit Voice Dial.

Note: You cannot use voice recognition to end a

5. Follow the prompts.

call; you must press the end key

slide is open.

when the

Erasing voice tags

To erase all voice name dial recordings in

your phone:

Setting up voice dialing

To make or receive calls using voice dialing,

contacts must be saved with associated voice tags.

1. Menu → Settings → Voice Features →

Erase Voice Dial.

2. Select Yes.

Creating a voice tag for a contact

1. Press the right softkey

to select Contacts.

Making a call using voice tags

1. If you haven’t already done so, record a voice

2. Highlight the contact and press

3. Press

down to highlight the number.

tag for the person you wish to call.

4. Press

to select Options.

2. With the slide open, from the home screen,

press the send/talk key

responds: “Say a name.”

. The phone

5. Highlight Add Voice Dial and press

6. Follow the voice prompts. You will need to say

3. Say the name of the person you want to call.

the name twice.

4. If the name you said matches a contact in the

Voice Dial List, the phone responds: “Calling

(Name).” Remain silent to make the call, or

say No to cancel.

Viewing entries with voice tags

•

Select Menu → Contacts → Voice Dial List.

A list of all contacts with assigned voice

tags appears.

Editing a voice tag

1. Select Menu → Contacts → Voice Dial List.

2. Highlight the contact to edit, and press

User Guide for the Kyocera Slider Jet Phone

Note: If the phone finds multiple voice tags

that sound like the name you said, you will be

asked to verify which name you want to call.

Say Yes when you hear the correct name. Say

No when you hear an incorrect name.

–

Say “Call” to dial the number.

Say “Verify” to cause phone to repeat the

set of digits that you input.

–

Say “Cancel” to exit voice recognizer and

return to the home screen.

5. When you are finished with the call,

Speak a digit to enter the next digit. Once

the phone repeats the digit, you can speak

the next digit or pause to hear the prompt.

press the end key

if the slide is open.

Making a call using digit dialing

When using digit dialing, you speak digits to dial a

phone number.

Using voice features with

hands-free car kits

You can use voice commands to make a phone

call or to answer the phone only if your phone is

connected to a professionally installed Kyocera

hands-free car kit (sold separately).

Note: You cannot speak a string of digits. You must

speak one digit at a time and wait for the prompt.

1. From the home screen, press the send/talk

key

. The phone responds: “Say a name

or say Dial.”

Note: The following features apply only to

2. Say “Dial”. The phone responds:

installed hands-free car kits unless noted.

“Speak a digit.”

To shop for hands-free car kits, visit

3. Speak the first digit of the phone number you

want to call. Once the phone repeats the digit,

you can speak the next digit.

www.kyocera-wireless.com/store or call

800-349-4188 (U.S.A. only) or 858-882-1410.

Waking up the phone

If you pause, the phone will prompt you with

the following five options. After the prompt,

speak an option.

If your phone is connected to a Kyocera installed

hands-free car kit, you can use the voice

command to activate the phone to make a

phone call.

–

Say “Clear” to erase the last digit entered.

The phone responds: “Digit cleared.”

To clear the entire phone number, say

“Clear” again. When the phone prompts

you with “Clear entire phone number?”,

say “Yes” to clear or “No” to cancel.

Note: Voice Wake-up does not work with

Keyguard active.

Using Voice Recognition

To activate the Voice Wake-up setting:

Answering using voice commands

1. Select Menu → Settings →

Voice Features → Voice Wake-Up →

With accessory.

If Auto-Answer is turned off, you can use a voice

command to answer an incoming call using the

installed hands-free car kit.

2. Select Menu → Settings → Keyguard →

•

Select Menu → Settings → Accessories →

Auto-Answer → Disabled.

Disabled, then press

To wake up the phone:

To activate the Voice Answer setting:

1. Say “Wake Up” and listen for a tone.

1. Select Menu → Settings →

Voice Features → Voice Answer.

2. Say “Wake Up” again until you hear two tones.

2. Highlight Enabled and press

If the phone does not recognize your

“Wake up” command, see “Training voice

recognition” on page 60.

3. Select Menu → Settings → Silent Mode →

Normal Sounds, then press

To answer a call:

Answering the phone

When you receive an incoming call, the phone

responds: “Incoming call, answer?” or “Incoming

roam call, answer?” If the caller is recognized as a

contact entry in your phone, then the phone will

say “Incoming call from (Name), answer?”

You can set your hands-free car kit to

(1) answer automatically or

(2) answer using a voice command.

Answering automatically

•

Say “Yes” or press any key except the

end key

You can set your phone to answer automatically.

Note: This setting also works with the portable

hands-free car kit.

Ignoring an incoming call

•

Select Menu → Settings → Accessories →

Auto-Answer → After 5 secs.

To ignore an incoming call, do one of

the following:

•

Say “No” and press the end key

silence the alert.

•

Remain silent. The voice alert repeats twice

and the phone rings once, then returns to the

home screen.

User Guide for the Kyocera Slider Jet Phone

Training voice recognition

If your phone is having trouble recognizing your

voice, you can train it with the commands Yes,

No, and Wake up.

1. Select Menu → Settings → Voice Features.

2. Select Voice Training.

3. Read the message and press the left softkey

to select OK and continue. Cancel

returns you to the previous screen.

4. Select Train All or the item you want to train.

5. Follow the prompts for each word until

training is complete.

Using Voice Recognition

13 USING TOOLS AND GAMES

Naming a saved voice memo

Voice Memo

The Voice Memo tool allows you to record and

play back audio memos.

1. Select Menu → Tools & Games →

Voice Memo → Recorded Memos.

2. Highlight the memo and select Options.

Recording a voice memo

3. Select Rename.

1. Select Menu → Tools & Games →

Voice Memo → Record New.

- or -

4. Press and hold

to clear the

default name.

5. Use the keypad to enter a name for the memo.

Press and hold

right.

6. Select Save.

2. Say your memo and press the left softkey

to select Stop.

Erasing a saved voice memo

3. Select Save to save your memo.

1. Select Menu → Tools & Games →

Note: If an incoming call is received while you’re

recording a memo, the memo is saved and the

incoming call screen appears.

Voice Memo → Recorded Memos.

2. Highlight the memo and select Options.

3. Select Erase. The prompt “Erase

file?” appears.

Playing or reviewing a voice memo

4. Select Yes or No.

1. Select Menu → Tools & Games →

Voice Memo → Recorded Memos.

Scheduler

The Scheduler allows you to schedule events and

set reminder alerts.

2. Highlight the voice memo to review and

select Play.

3. Press

and press

Play

right and left to select a function

to perform it:

Creating an event

1. Select Menu → Tools & Games →

Stop

Pause

Scheduler → Add New Event.

2. Enter a name for the event and press

down. For help entering text, see page 21.

User Guide for the Kyocera Slider Jet Phone

3. Select Options and classify the type of event

and press : Meeting, Phone Call, Birthday,

Anniversary, Vacation, Medical, or Other.

10. Press

recurring event.

Select an option and press

Weekly, Monthly, or Annually.

to select whether or not this is a

–

: No, Daily,

4. Press

to change the date of the event (the

current date is the default date of the event).

11. Select Save.

–

Press

left or right to move between the

Editing, erasing, or sending an event

month, day, and year fields.

1. Select Menu → Tools & Games →

Press

month, day, or year.

up or down to change the

Scheduler → View Month.

2. Press

up, down, left or right to highlight

Press

to save your changes.

the day with the event to view, edit, or erase

5. Press

to set the time of the event.

and press

3. Press

and press

–

Press

left or right to move between the

up or down to highlight the event

hour, minute, and AM/PM fields.

Press

minute, or AM/PM.

Press to save your changes.

up or down to change the hour,

4. Press the right softkey

5. Select Edit, Erase, or Send and press

to select Options.

–

For more information about editing the

6. Press

to set the duration of the event.

event, see “Scheduler” on page 61.

–

Press left or right to move between the

–

To erase the event, highlight Erase

hour and minute fields.

Press up or down to change the hour

and minute.

Press to save your changes.

and press

. Press the left softkey

to confirm.

–

For more information about sending the

event, see “Sending and Receiving Text

Messages” on page 24.

7. Press

to set a reminder of the event.

–

Select an option and press

8. Press

–

to set the reminder sound.

Select an option and press

9. Press

to select a Silent Mode setting

–

Select No or During Event and press

Using Tools and Games

Setting the QuickAlarm

Alarm Clock

You can set up to four alerts with your phone’s

three alarm clocks and one quick alarm.

1. Select Menu → Tools & Games →

Alarm Clock.

2. Highlight QuickAlarm and select Set.

Note: The alert occurs only if the phone is on.

3. Select an option and press

minutes (default), 30 minutes, or 60 minutes.

A message appears telling you the

QuickAlarm is On.

: 5 minutes, 15

Setting an alarm clock

1. Select Menu → Tools & Games →

Alarm Clock.

2. Highlight one of the alarms and select Set.

4. When the alarm rings, select Off to turn off the

alarm or Reset to set the QuickAlarm again.

3. Use the phone keypad to enter numbers and

to switch between AM and PM.

Tip Calculator

The Tip Calculator helps you calculate how much

tip to include with a bill.

–

Press

hours, minutes, and AM/PM fields.

Press up or down to change the

hours, minutes, and AM/PM options.

4. Press to set the time of the alarm.

5. Select Options to set the alarm sound.

6. Highlight an option and press

7. Select Options to set the recurring time.

8. Highlight an option and press

9. Enter a note for the alarm and press

left or right to move between

–

1. Select Menu → Tools & Games →

Tip Calculator.

2. Enter the amount of your bill.

3. Select Next.

4. Select the amount you want to include as a tip

(10%, 15%, 18%, 20%, Other) and press

. Your total bill appears, including tip.

5. To split the bill, press the right softkey

10. Press the left softkey

to select Save and

select Split.

set the alarm(s).

6. Press

7. Enter the number of guests and press the left

softkey to select Next. The amount each

to clear the default of 2 guests.

11. When the alarm rings, select Off to turn off the

alarm or Snooze to silence the alarm for

10 minutes.

guest pays is calculated.

Note: Opening the slide turns off the alarm.

8. Select Done.

User Guide for the Kyocera Slider Jet Phone

Calculator

Use the calculator for basic

mathematical equations.

Timer

This timer counts down for a specified

amount of time. It beeps when that amount

of time has elapsed.

1. Select Menu → Tools & Games → Calculator.

2. Use the keypad to enter numbers.

1. Select Menu → Tools & Games → Timer.

2. Select Set.

3. Use

to select mathematical operations:

–

Press

to move the cursor left or right.

up or down to set the hours,

Left x (multiply) Up

+ (add)

Right ÷ (divide)

4. Press

Example: Enter 5, press

Down - (subtract)

minutes, and seconds.

to calculate the result.

left to select X,

to obtain the

3. Select Start to begin the countdown.

Select Stop to pause the countdown.

Select Reset to clear the timer.

enter 2, then press

result of 10.

4. Select Sound to set the alarm sound and

5. Press the end key

home screen.

- or -

to return to the

press

5. Press the end key

to silence the alarm.

or the right softkey

Press

to clear the screen.

Options

Stopwatch

1. Select Menu → Tools & Games →

Adds displayed digit to the value

stored in memory.

M+

Stopwatch.

Displays currently stored value on

screen.

2. Select Start to begin counting.

Select Stop to stop counting.

Select Reset to clear the counter.

Clears value currently stored in

memory.

Using Tools and Games

Games

Race 21

The games in this section may not be available

on your phone. Check with your service provider

for availability.

This game is a timed variation of Black Jack. Each

game comprises three 90-second rounds. To

score points, add cards in each of the four

columns, trying to reach but not exceed 21 in

each column within during the course of

the game.

If you receive an incoming call alert while you are

playing a game, the game is paused and exited.

You can return to play once the call alert ends.

Games do not remain paused if the phone is

turned off or loses power.

1. Select Menu → Tools & Games → Race 21.

2. Press

to select Yes at the prompt, “Dim

backlight to conserve battery?”

Brick Attack

3. Select New Game. The first card to be placed

is shown at the top left of the screen. Press a

key to add a card to the row as follows:

The goal of this game is to eliminate bricks

arranged in levels. You send a moving ball

upward using a paddle at the bottom of

the screen.

Add cards to the first row

Add cards to the second row

Add cards to the third row

Add cards to the fourth row

1. Select Menu → Tools & Games →

Brick Attack.

2. Press

to select Yes at the prompt, “Dim

backlight to conserve battery?”

Shortcut: Press

left or right to choose

3. Press

to select New.

arrows at the bottom of the screen then press

to add cards to corresponding rows.

–

To pause the game, press

press to Resume.

To move the paddle, press

or right.

To exit the game, highlight Exit and

press

, then

Note: Each time you place a card, a new card

appears for placement.

–

left

4. Continue placing cards until you are satisfied

with your selections.

–

You can pause or end the game at any time

by pressing the end key

You lose points each time you exceed 21

in a column.

User Guide for the Kyocera Slider Jet Phone

–

Select Skip to skip one card per round.

5. Press to select to get your score and

advance to the next round.

6. Select an option and press

to select it.

–

New Game initiates game play. To pause

the game, press . From here you

can choose Resume, New or Quit.

–

Resume Game returns you to the game

you were last playing.

Scoreboard provides you with the top

five scores.

Music plays music with this game. Select

from Music Always, Sound Effects,

Instructions, Credits, During Title, or

No Music.

7. Press the end key

to end all games.

Using Tools and Games

14 USING MEDIA GALLERY

The Media Gallery stores camera pictures,

images, audio files, and videos in the phone and

displays those files on the phone’s screen.

Press the right softkey

to select Options:

–

Send launches the messaging application

so you can share the photo.

Take Picture to snap another photo.

Erase the image.

Send To Online to save the picture to the

Online Album.

–

Accessing files

1. Select Menu → Media Gallery.

2. Select an option:

–

Assign picture as a Caller ID or

as wallpaper.

Lock to prevent accidentally erasing

the photo.

–

Camera Pictures displays thumbnails of

the photos you have taken in

chronological order.

–

Images displays a list of categories that

contain preloaded, downloaded, saved, or

created files such as wallpaper, screen

savers, or caller IDs.

–

Rename the photo.

Move File from the phone to the card.

Copy File from the phone to the card.

Details of the file.

Erase All erases all pictures stored

(pictures must not be locked).

–

Sounds displays a list of categories that

contain saved or downloaded sounds such

as ringers and voice memos, as well as

audio files on an inserted Transflash

(microSD) card.

3. When you have chosen to view the picture

(the image fills the display area, press the

right softkey

to select Options:

Videos displays a list view of the file names

of videos that you recorded.

–

Erase the image.

Assign picture as a Caller ID or

as wallpaper.

Browsing pictures

1. Select Menu → Media Gallery →

–

Modify allows you to select the following

from the next Options menu: Rotate,

Resize, Brightness, Sharpness, Saturation,

Hue, Auto Adjust, Color Tone.

Send To Online to save the picture to the

Online Album.

Camera Pictures.

2. Highlight a picture and press the left softkey

to select View.

–

- or -

User Guide for the Kyocera Slider Jet Phone

–

Zoom allows you to zoom in or out on

the picture.

Take Picture to snap another photo.

Lock to prevent accidentally erasing

the photo.

–

Send To Online to save the image to the

Online Album.

Lock to prevent accidentally erasing

the image

Erase the image (image must not be

locked).

Rename the image.

Details gives you the file size of the image.

Erase All erases all images stored (images

must not be locked).

–

Rename the photo.

Move File from the phone to the card.

Copy File from the phone to the card.

Details of the file.

–

4. Or press the left softkey to Erase the image.

4. Select Close or press

when done.

Browsing images

The images menu allows you to assign your files

to various applications.

Browsing sounds

1. Select Menu → Media Gallery → Sounds.

2. Highlight an option and press

1. Select Menu → Media Gallery → Images.

2. Highlight an option and press

–

Saved Sounds contains sounds saved on

your phone.

Music displays audio files on Transflash

(microSD) card.

Ringers contains ringers saved on

your phone.

–

Saved Images displays available images.

Wallpapers displays wallpaper selections.

Screen Savers displays available

screensavers.

–

Caller IDs displays pictures and images

saved and the text IDs you assigned them.

Voice Memos contains voice memos you

made to yourself.

3. Press the left softkey

- or -

to select View.

3. Highlight an option and press

(options

vary according to selection):

Press the right softkey

to select Options

(options vary according to selection):

–

Assign as the default ringer or contact

ringer.

Send To Online to save the sound file to

the Online Album.

Play all to start the music player.

–

Send launches the messaging application

so you can share the image.

Set as Default to assign the image as a

wallpaper or screen saver.

Assign to assign the image to a contact.

Using Media Gallery

–

Record New allows you to record

new videos.

–

Send To Online to save the video to the

Online Album.

–

Erase the sound file.

–

Move File from the phone to the card.

Copy File from the phone to the card.

Lock to prevent accidentally erasing

the video.

Unlock if the song is locked.

Lock to prevent accidentally erasing

the song.

–

Rename allows you to rename the

sound file.

Details gives you the name, size, date and

locked/unlocked status of the music file.

Erase All erases all songs stored.

–

Rename allows you to rename the

video file.

Details gives you the file size and date of

the video.

Erase All erases all videos stored.

4. Select Close when done.

4. Press

- or -

to return to the Videos menu.

Browsing videos

1. Select Menu → Media Gallery → Videos.

Press

to exit the Media Gallery.

2. Highlight an option and press

–

Video Album contains videos taken with

your camera.

–

Saved Videos contains videos that

were downloaded.

3. Select Play to review a video. Use

highlight Play

or Rotate Right

- or -

, Stop

, Rotate Left

Select Options and choose from the

following options:

–

Send launches the messaging application

so you can share the videos.

Record New allows you to record

new videos.

Erase the video.

User Guide for the Kyocera Slider Jet Phone

15 GETTING HELP

India:

Toll free#: 1-600-121214

Toll#: 0124-284-5000

Customer support

Your service provider’s customer support

Mexico:

001-866-650-5103

department may be accessible directly from your

phone when you dial a number, such as *611

(check with your service provider). They can

answer questions about your phone, phone bill,

call coverage area, and specific features available

to you, such as call forwarding or voicemail.

New Zealand: 0-800-990-100

Panama:

Peru:

001-800-201-1984

0-800-51-934

Puerto Rico:

Venezuela:

1-866-664-6443

0-800-100-2640

For questions about the phone features, refer to

the materials provided with your phone, or visit

www.kyocera-wireless.com.

Before requesting support, please try to

reproduce and isolate the problem. When you

contact the Customer Care Center, be ready to

provide the following information:

For additional questions, you may contact the

Kyocera Wireless Corp. Customer Care Center in

any of the following ways:

•

The name of your service provider.

The actual error message or problem you

are experiencing.

•

Web site: www.kyocera-wireless.com

Email: [email protected]

•

The steps you took to reproduce the problem.

The phone’s electronic serial number (ESN).

Phone: 1-800-349-4478 (U.S. and Canada)

or 1-858-882-1401.

–

To locate the ESN select Menu →

Phone Info and scroll down to ESN: for the

11-digit number.

•

Customer support phone numbers are also

available in the following countries:

Argentina:

Australia:

Brazil:

0-800-666-0052

1-800-507-000

0-800-55-2362

800-43-1212

Qualified service

If the problem with your phone persists, return

the phone with all accessories and packaging to

the dealer for qualified service.

Chile:

Colombia:

01-800-700-1546

Getting Help

Phone accessories

To shop for KX18 phone accessories, visit

www.kyocera-wireless.com/store. You may also

call us at 800-349-4188 (U.S.A. only) or

858-882-1410.

Become a product evaluator

To participate in the testing and evaluation of

Kyocera Wireless Corp. products, including

cellular or PCS phones,

visit beta.kyocera-wireless.com.

User Guide for the Kyocera Slider Jet Phone

INDEX

Numerics

1-Touch dialing, 13

custom menu

creating, 47

hard pause, 17

icons, 8

Alarm Clock, 8

alarm clock, 63

alerts

for messages, 46

for missed calls, 12

auto-hyphenation, 48

data/fax setup, 15, 51

digital mode, 8

display contrast, 48

contacts, 19

messages, 27

InBox, 28

emergency

language, 47

lights

calls, 14

emergency mode, 14

exit emergency mode, 14

position location, 8, 52

erasing

contact entries, 19, 50

phone numbers, 19

text messages, 29

external storage card, 31

lights-only mode, 8, 44

banner, 47

battery, 1

blocking outgoing calls, 50

Brick Attack, 65

limiting calls out, 50

lock code, 49

locking

phone, 49

calculator, 64

call counters, 14

callback number, 25

calls

memory

saving, 29

menu view, 47

microSD/Transflash card, 31

Music Player, 34

fast find, 20

fax mode, 51

finding contact information, 20

frequent contacts, 20

answering, 9

missed, 11

redialing, 10

number mode, 21

camera

games

menu options, 39

recording video, 41

sending a picture, 39

setting up, 40

taking a picture, 40

color themes, 49

Com Port speed, 51

contacts directory, 17

contrast, 48

OutBox, 27

Brick Attack, 65

Race 21, 65

phone numbers

erasing, 19

verifying your own, 6

phone, unlocking, 50

position location, 8, 52

hands-free car kit

answering using voice, 59

purchasing, 71

hands-free headset

purchasing, 71

countdown timer, 64

QuickAlarm, 63

QuickText, 25, 30

timer, 64

timing calls, 14

tip calculator, 63

Transflash/microSD card, 31

TTY/TDD, 52

Race 21, 65

recent call icons, 12

resetting the phone, iv

ringers

choosing types, 44

for contacts, 18

for roaming calls, 15

silencing, 7

unlocking the phone, 50

vCard, 19

vibrate, 8, 44

Voice Answer, 59

voice dialing, 57

voice memo

erasing, 61

naming, 61

recording, 61

voicemail, 13

setting up, 7

volume

volume, 45

roaming, 8

alerts, 15

controlling, 15

ringer, 15

scheduler, 61

screen contrast, 48

screen icons, 8, 21, 27, 44

screen savers, 48

secret contacts, 12, 19

security, 49

earpiece, 10, 45

key beep, 46

ringer, 45

sent messages, 26

silent mode, 8, 44

smart sound, 45

smiley mode, 22

songs, 34

wallpaper, 49

Web Browser, 36

speed dialing, 19

stopwatch, 64

symbol mode, 22

technical support, 70

text entry, 21

quick reference, 23

text messages, 24

time format, 49

User Guide for the Kyocera Slider Jet Phone

Motorola MOTORAZR V8 User Manual
LG Electronics Nite User Manual
JVC KD S100 User Manual
Imation Nano Flash Drive User Manual
HTC Desire Desire User Manual
Hitachi Deskstar HDS721016CLA682 User Manual
Fujitsu MPD3XXXAT User Manual
Dakota Digital MULTI GAUGE UTV 1200 User Manual
Apple iPhone 3G A1303 User Manual
ABB GE GEH3418 User Manual